Dancryl
635-0XX Dancryl Acrylic Post-Cat Clear TC
Product Codes:
635-015 15° Matte
635-035 35° Satin
635-090 90° High Gloss
Surface Preparation:
Wood substrate should be sanded with 120, 150 or 180 grit paper prior to staining or coating. Sealers should be sanded with 280/320 grit stearated paper prior to topcoating. Appropriate sealers are self seal or catalyzed 401 line vinyl sealer. When recoating, the sealer or previous coat must be sanded and the next coat applied within eight hours. Stain systems under acid containing coatings should be acid stable. Dancryl can not be used on metal, old oil or cellulose lacquers.
General Information:
Agitate material before use. Always mix Dancryl while adding hardener and reducers in the recommended mixing ratios. Dancryl must be agitated thoroughly at all times to ensure product consistency and consistent gloss.
Apply at 3-5 mils wet on sanded substrate. Further coats may be applied after complete drying followed by sanding with 280/320 grit stearated paper.
Contact with metal surfaces should be avoided.
Maximum film build of Dancryl should not exceed 4 mils dry. Maximum film build of total coating system must not exceed 4 mils dry.
To obtain a complete cure, the system should be applied at an ambient temperature above 18ºC and a relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapors. Finished surfaces must not be cleaned with ammonia containing products.
This product could be used as a self seal or over catalyzed vinyl sealer 401-004.
PDF Name: CA-PIS_635-0XX_Dancryl_Acrylic_Post-Cat_Clear_TC
Tack Free Time: 20 minutes
Files: CA-PIS_635-0XX_Dancryl_Acrylic_Post-Cat_Clear_TC.pdf
Dry to Sand : 6 hours
Dry to Stack: Overnight
Tack Free Time: Flash off before entering oven
Dry to Sand: 2 hours
VOC less exempt g/l: 582
VOC g/l: 582
Dry to Stack: 3 hours
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
Dancryl is a two component, acrylic lacquer designed for all types of wood for interior use. It provides a smooth, hard wearing surface that is resistant to alcohol, water, grease and usual household chemicals. Dancryl is especially suited for topcoating light coloured basecoats due to its good light stability and water white appearance.
spec_uses:
Dancryl is used on interior wood when clarity and light stability are very important.
Suggested Uses: Spray
Mixing Ratio:
8% with 999-017 by volume
Pot Life:
8 hours
Application Viscosity:
Zahn #2 signature cup 20-25 seconds
Reducer: 121-8020 or 121-803
Retarder: 800-5328 EEP
Clean-up Solvent: Lacquer Thinner
Recommended Wet Film: 3-5 wet mils
Coverage:
13 m²/l (145 pi²/l) at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.
Note application:
N/A
Viscosity:
Zahn #2 signature cup 40 sec at 25°C
Flash Point: 14°C (57°F)
Density (lb/gal): 0.95
Solid (% by weight): 39%
Solid (% by volume): 34%
Shelf Life (months): 12

Dancryl

635-0XX Dancryl Acrylic Post-Cat Clear TC

Find distributor Trouver un distributeur

spec_description:

Dancryl is a two component, acrylic lacquer designed for all types of wood for interior use. It provides a smooth, hard wearing surface that is resistant to alcohol, water, grease and usual household chemicals. Dancryl is especially suited for topcoating light coloured basecoats due to its good light stability and water white appearance.

BACKRetour

Product codeCodes de produit
Product Codes:

635-015 15° Matte
635-035 35° Satin
635-090 90° High Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #2 signature cup 40 sec at 25°C
Flash Point: 14°C (57°F)
Density (lb/gal): 0.95
Solid (% by weight): 39%
Solid (% by volume): 34%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_635-0XX_Dancryl_Acrylic_Post-Cat_Clear_TC.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more