E.S. Lacquer
131-51XX ES Lacquer White Pre-Cat Pigmented Topcoat
Product Codes:
131-5120 20° Low Gloss
131-5135 35° Satin
131-5150 50° Semi-Gloss
131-5190 90° High Gloss
Surface Preparation:
Wood substrate should be sanded with 120, 150 or 180 grit paper prior to staining or coating. Sealers should be sanded with 280/320 grit stearated paper prior to topcoating. The sealer should be topcoated within eight hours of sanding. When recoating, the previous coat of E.S. Lacquer must be sanded and the next coat applied within eight hours. E.S. Lacquer cannot be used on metal, old oil or cellulose lacquer.
General Information:
Agitate material before use. Always mix E.S. Lacquer while adding hardener and reducers in the recommended mixing ratios. E.S. Lacquer must be agitated thoroughly at all times to ensure product consistency and consistent gloss.
Apply at 3-5 mils wet on sanded substrate. Further coats may be applied after complete drying followed by sanding with 280/320 grit stearated paper.
Maximum film build of E.S. Lacquer should not exceed 4 mils dry. Maximum film build of total coating system must not exceed 4 mils dry. To obtain a complete cure, the system should be applied at an ambient temperature above 18ºC and a relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapors. Finished surfaces must not be cleaned with ammonia containing products.
Basecoats to use with 131-51XX: 225-0010, 522-1624, 545-8016, 546-7257 or self-seal
PDF Name: CA-PIS_131-51XX_ES_Lacquer_White_Pre-Cat_Pigmented_Topcoat
Tack Free Time: 15 minutes
Files: CA-PIS_131-51XX_ES_Lacquer_White_Pre-Cat_Pigmented_Topcoat.pdf
Dry to Sand : 2 hours
Dry to Stack: 3 hours
Tack Free Time: Flash off before entering oven
Dry to Sand: 30 minutes
VOC less exempt g/l: 652
VOC g/l: 652
Dry to Stack: 1 hour
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
E.S. Lacquer is a one-component, Pre-Catalyzed lacquer especially developed for surface treatment of furniture where a beautiful appearance with good resistance properties is desired. E.S. Lacquer is fast drying and well suited for spraying as well as coating by roller and curtain coating.
spec_uses:
The material is used to achieve an open or semi-open grain finish on all types of wood for interior use. To augment the chemical resistance of the product, E.S. Lacquer 131-51XX may be catalyzed.
Suggested Uses: Spray
Mixing Ratio:
3% 873-0870 or 999-017 if catalyzed
Pot Life:
8 hours if catalyzed
Application Viscosity:
Zahn #2 signature cup 20-22 seconds
Reducer: 121-8020 or 121-803
Retarder: 800-5328 EEP
Clean-up Solvent: Lacquer Thinner
Recommended Wet Film: 3-5 wet mils
Coverage:
10 m²/l (105 pi²/l) at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.
Note application:
N/A
Viscosity:
Zahn #2 signature cup 45 sec at 25°C
Flash Point: 14°C (57°F)
Density (lb/gal): 1.09
Solid (% by weight): 40%
Solid (% by volume): 25%
Shelf Life (months): 12

E.S. Lacquer

131-51XX ES Lacquer White Pre-Cat Pigmented Topcoat

Find distributor Trouver un distributeur

spec_description:

E.S. Lacquer is a one-component, Pre-Catalyzed lacquer especially developed for surface treatment of furniture where a beautiful appearance with good resistance properties is desired. E.S. Lacquer is fast drying and well suited for spraying as well as coating by roller and curtain coating.

BACKRetour

Product codeCodes de produit
Product Codes:

131-5120 20° Low Gloss
131-5135 35° Satin
131-5150 50° Semi-Gloss
131-5190 90° High Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #2 signature cup 45 sec at 25°C
Flash Point: 14°C (57°F)
Density (lb/gal): 1.09
Solid (% by weight): 40%
Solid (% by volume): 25%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_131-51XX_ES_Lacquer_White_Pre-Cat_Pigmented_Topcoat.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more