Catlac
431-30XX Catlac Pre-Cat Low VOC Clear Topcoat
Product Codes:
431-3010 10° Matte
431-3025 25° Low Gloss
431-3035 35° Satin
431-3050 50° Semi-Gloss
431-3090 90° High Gloss
Surface Preparation:
Sealer must be sanded with a #280/320 grit stearated paper and free of dust and all contaminants before application of the topcoat. Catlac must not be applied over metal, old finish or nitrocellulose lacquer. Stain systems used should be acid stable.
General Information:
Agitate material before use. Keep under mixing to ensure product consistency and consistent gloss. Apply at 3- 5 mils on sanded sealer. One extra coat may be applied after complete drying followed by sanding with 280/320 grit stated paper. The subsequent coat must be applied the same day as the previous coat is sanded. Maximum film build of the topcoat should not exceed 2 mils dry. Maximum film build of the system should not exceed 4 mils dry. Eliminate all contact with metallic surfaces. Catlac must not be polluted with oil, varnish or the like and must not be sanded with steel wool between coats.
To obtain complete cure, Catlac should be applied at a temperature above 18°C and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapours. Finished surfaces must not be cleaned with ammonia containing products. Always use plastic or stainless equipment to eliminate discoloration due to oxidation.
Sealers to use with 431-30XX: 390-0060, 431-1219, 546-8003 and 546-5192.
Natural ambering or discoloring in the can may occur over time. Although there may be changes of color in the can as the product ages, this will have little to no effect on the product during application. Storing in locations above recommended room temperatures could accelerate ambering.
PDF Name: CA-PIS_431-30XX_Catlac_Pre-Cat_Low_VOC_Clear_Topcoat
Tack Free Time: 20 - 30 minutes
Files: CA-PIS_431-30XX_Catlac_Pre-Cat_Low_VOC_Clear_Topcoat.pdf
Dry to Sand : 45 - 60 minutes
Dry to Stack: 8 hours
Tack Free Time: Flash off before entering oven
Dry to Sand: 30 - 45 minutes
VOC less exempt g/l: 654
VOC g/l: 578
Dry to Stack: 2 hours
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
Catlac is a one component, ready to use, Pre-Catalyzed Reactive Amino Coating (RAC). This product dries quickly and demonstrates good household wear, household chemical and solvent resistance.
Special Recognition: Meets Kitchen Cabinet Manufacturer Associations (KCMA) Standards.
spec_uses:
Recommended for office and household furniture, kitchen cabinets as well as many other interior wood applications.
Suggested Uses:
Wood Finish / Spray
Mixing Ratio:
N/A
Pot Life: N/A
Application Viscosity:
25 ± 2 sec Zahn #2 at 25°C
Reducer: 5-10% of 121-8020 or 121-803 if necessary
Retarder: 800-5328 EEP
Clean-up Solvent: Lacquer Thinner
Recommended Wet Film: 3 to 5 wet mils
Coverage:
8 m²/l (85 pi²/l) at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.
Note application:
N/A
Viscosity:
Zahn #2 signature cup 25 sec at 25°C
Flash Point: -4°F (-20°C)
Density (lb/gal): 0.92 ± 2% at 25°C
Solid (% by weight): 27 ± 2%
Solid (% by volume): 20 ± 2%
Shelf Life (months): 12

Catlac

431-30XX Catlac Pre-Cat Low VOC Clear Topcoat

Find distributor Trouver un distributeur

spec_description:

Catlac is a one component, ready to use, Pre-Catalyzed Reactive Amino Coating (RAC). This product dries quickly and demonstrates good household wear, household chemical and solvent resistance.

Special Recognition: Meets Kitchen Cabinet Manufacturer Associations (KCMA) Standards.

BACKRetour

Product codeCodes de produit
Product Codes:

431-3010 10° Matte

431-3025 25° Low Gloss

431-3035 35° Satin

431-3050 50° Semi-Gloss

431-3090 90° High Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #2 signature cup 25 sec at 25°C
Flash Point: -4°F (-20°C)
Density (lb/gal): 0.92 ± 2% at 25°C
Solid (% by weight): 27 ± 2%
Solid (% by volume): 20 ± 2%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_431-30XX_Catlac_Pre-Cat_Low_VOC_Clear_Topcoat.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more