V-Seal
546-5192 V-Seal Low VOC Clear Vinyl Sealer
Product Codes:
546-5192 V-Seal
Surface Preparation:
Wood must be sanded with a #120, 150 or 180 grit paper and free of dust and all contaminants. Before application of the topcoat, sealer must be sand with a 280/320 grit paper. V-Seal must not be used over metal, old oil finish or cellulosic finish.
General Information:
Apply 3-4 mils wet on sanded surface by spray. If more than 4 mils, sanding becomes difficult. Never exceed a thickness of 5 mils by coat as the solvent will remain trapped in the film and this may cause stress in the film. Maximum film build of the sealer should not exceed 1 mil dry. Maximum film build of the system should not exceed 4 mils dry.
To obtain complete cure, the product must be applied at a temperature above 18ºC and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapors. Finished surface must not be cleaned with ammonia containing products.
V-seal is use with topcoat: 421-55XX, 421-63XX, 421-67XX, 421-72XX, 482-3XX, 431-22XX, 431-30XX, 431-90XX and 431-98XX.
PDF Name: CA-PIS_546-5192_V-Seal_Low_VOC_Clear_Vinyl_Sealer
Tack Free Time: 10 - 15 minutes
Files: CA-PIS_546-5192_V-Seal_Low_VOC_Clear_Vinyl_Sealer.pdf
Dry to Sand : 20 - 25 minutes
Dry to Stack: 2 hours
Tack Free Time: Flash off before entering oven
Dry to Sand: 15 - 20 minutes
VOC less exempt g/l: 724
VOC g/l: 552
Dry to Stack: 30 - 45 minutes
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
Low-VOC vinyl sealer. It is a single pack, quick drying product with excellent sanding and sealing properties. This product is recommended for Kitchen Cabinet or Furniture due to its excellent resistance to moisture. V-Seal contains no formaldehyde.
spec_uses:
V-Seal is used for sealing wooden furniture and other wood surfaces for interior use only. It can be used on all wood types.
Suggested Uses:
Spray
Mixing Ratio:
N/A
Pot Life: N/A
Application Viscosity:
14-16 sec Zahn #2 at 25°C
Reducer: Lacquer Thinner 803-1339/121-001 or 121-8020
Retarder: 800-5328 EEP
Clean-up Solvent: Lacquer Thinner
Recommended Wet Film: 3 to 4 mils wet
Coverage:
5 m²/l (50 pi²/l) at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.
Note application:
N/A
Viscosity:
Zahn #2 signature cup 15 sec at 25°C
Flash Point: -20°C
Density (lb/gal): 0.89 ± 2% at 25°C
Solid (% by weight): 17%
Solid (% by volume): 12%
Shelf Life (months): 12

V-Seal

546-5192 V-Seal Low VOC Clear Vinyl Sealer

Find distributor Trouver un distributeur

spec_description:

Low-VOC vinyl sealer. It is a single pack, quick drying product with excellent sanding and sealing properties. This product is recommended for Kitchen Cabinet or Furniture due to its excellent resistance to moisture. V-Seal contains no formaldehyde.

BACKRetour

Product codeCodes de produit
Product Codes:

546-5192 V-Seal

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #2 signature cup 15 sec at 25°C
Flash Point: -20°C
Density (lb/gal): 0.89 ± 2% at 25°C
Solid (% by weight): 17%
Solid (% by volume): 12%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_546-5192_V-Seal_Low_VOC_Clear_Vinyl_Sealer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more