V-Primer
546-7257 V-PRIMER BLANC
Product Codes:
546-7257 V-PRIMER BLANC
Surface Preparation:
Wood must be sanded with a #120 or 150 grit paper and free of dust and all contaminants.
General Information:
To assure consistency, always agitate while catalyzing, reducing and applying. Apply one or two coats. A good sanding between coats with a #280/320 grit paper is necessary to obtain a good adhesion. If catalyzed, topcoat must be applied within 8 hours of sanding. Never apply more than 5 mils wet in one coat. Dry film thickness of V-Primer should not exceed 2 mils dry. Total dry film thickness of system should not exceed 5 mils dry. For any other information, contact your sales representative.
To obtain complete cure, the primer must be applied at a temperature above 18ºC and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapours. Finished surface must not be cleaned with ammonia containing products.
V-Primer blanc is use with topcoat: 117-30XX, 421-67XX, 484-6XXX
PDF Name: CA-PIS_546-7257_V-Primer_Pigmented_Vinyl_Primer
Tack Free Time: 45-60 min
Files: CA-PIS_546-7257_V-Primer_Pigmented_Vinyl_Primer.pdf
Dry to Sand : 60-90 min
Dry to Stack: 3-4 hours
Tack Free Time: Flash off before entering oven
Dry to Sand: 45-60 min
VOC less exempt g/l: 643
VOC g/l: 574
Dry to Stack: 1-2 hours
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
Vinyl primer with good adhesion to substrate and good humidity resistance.
spec_uses:
Used as a protective coatings for wood. For interior uses only.
Suggested Uses: Spray
Mixing Ratio:
N/A
Pot Life: N/A
Application Viscosity:
20 - 24 sec Zahn #2 at 25°C
Reducer: 803-1339 if needed
Retarder: N/A
Clean-up Solvent: 803-1339
Recommended Wet Film: 3 to 5 mils wet
Coverage:
N/A
Note application:
N/A
Viscosity:
20 - 24 sec Zahn #2 at 25°C
Flash Point: -18°C
Density (lb/gal): 1.08 ± 2% at 25°C
Solid (% by weight): 39 ± 1%
Solid (% by volume): 20 ± 1%
Shelf Life (months): 6

V-Primer

546-7257 V-PRIMER BLANC

Find distributor Trouver un distributeur

spec_description:

Vinyl primer with good adhesion to substrate and good humidity resistance.

BACKRetour

Product codeCodes de produit
Product Codes:

546-7257 V-PRIMER BLANC

Product information

Product specificationsSpécifications du produit

Viscosity:
20 - 24 sec Zahn #2 at 25°C
Flash Point: -18°C
Density (lb/gal): 1.08 ± 2% at 25°C
Solid (% by weight): 39 ± 1%
Solid (% by volume): 20 ± 1%
Shelf Life (months): 6

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_546-7257_V-Primer_Pigmented_Vinyl_Primer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more