Acryllak
228-95XX Acryllak White WB Pigmented Topcoat
Product Codes:
228-9520 20° Low Gloss
228-9535 35° Satin
228-9550 50° Semi-Gloss
Surface Preparation:
Substrate to be coated should be sanded with 150 or 180 grit sandpaper prior to coating. This product should be primed using Aquaprime.
General Information:
Add water as required and mix material before use. Apply by spray at wet film builds of 3-5 mils. Application and drying conditions must be at temperatures of 18°C or higher and at a humidity of less than 65%. Increased air flow or drying temperatures, including the use of infrared, will greatly decrease dry times.
Further coats may be applied after complete drying followed by sanding with 280/320 grit sandpaper. Second coat must be applied the same day as the board is sanded.
Product must be agitated thoroughly at all times to ensure product consistency. Contact with metal surfaces should be avoided. Film build should not exceed 2 dry mils per coat.
Total film build must not exceed 5 dry mils.
PDF Name: CA-PIS_228-95XX_Acryllak_White_WB_Pigmented_Topcoat
Tack Free Time: 20 minutes
Files: CA-PIS_228-95XX_Acryllak_White_WB_Pigmented_Topcoat.pdf
Dry to Sand : 2 - 3 hours
Dry to Stack: 24 hours
Tack Free Time: Flash off before entering oven
Dry to Sand: 60 minutes
VOC less exempt g/l: 215
VOC g/l: 102
Dry to Stack: 8 hours
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
Acryllak White is an acrylic modified polyurethane waterborne solid colour finish. Acryllak is a wear resistant, fast drying and environmentally friendly pigmented lacquer. It is resistant to conventional detergents and household cleaners.
spec_uses:
Acryllak is designed for wooden surfaces in general, and can be used as a topcoat for waterborne primers. It can be used for various surfaces when properly prepared. The inherently high viscosity allows this product to be applied by roller or brush as well.
Suggested Uses:
Pigmented Waterborne Topcoat
Mixing Ratio:
N/A
Pot Life:
N/A
Application Viscosity:
Zahn #4 signature cup 53 seconds
Reducer: Water, Use less than 5%, viscosity drops quickly
Retarder: N/A
Clean-up Solvent: Use water when wet, 4:1 water:800-5742 if dried
Recommended Wet Film: 3-5 mils wet
Coverage:
N/A
Note application:
N/A
Viscosity:
Zahn #4 signature cup 53 sec at 25°C
Flash Point: >93°C (200F)
Density (lb/gal): 1.18
Solid (% by weight): 47 ± 1%
Solid (% by volume): 37 ± 1%
Shelf Life (months): 12

Acryllak

228-95XX Acryllak White WB Pigmented Topcoat

Find distributor Trouver un distributeur

spec_description:

Acryllak White is an acrylic modified polyurethane waterborne solid colour finish. Acryllak is a wear resistant, fast drying and environmentally friendly pigmented lacquer. It is resistant to conventional detergents and household cleaners.

BACKRetour

Product codeCodes de produit
Product Codes:

228-9520 20° Low Gloss
228-9535 35° Satin
228-9550 50° Semi-Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #4 signature cup 53 sec at 25°C
Flash Point: >93°C (200F)
Density (lb/gal): 1.18
Solid (% by weight): 47 ± 1%
Solid (% by volume): 37 ± 1%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_228-95XX_Acryllak_White_WB_Pigmented_Topcoat.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more