CHEMLACK WHITE Pigmented Topcoat

230-27XX Chemlack 550 White NC Pigmented TC

Product Codes:

230-2720 Low Gloss
230-2740 Satin
230-2760 Semi-Gloss
230-2780 High Gloss

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit stearated paper prior to staining or coating. Primers, if used, should be sanded prior to being coated with 280/320 grit stearated paper. Appropriate primers are Chembase 550 White 545-5513, or self‑seal. Chemlack 550 White cannot be used on metal or old oil finishes.

General Information:

Agitate material before use. Chemlack 550 White must be agitated thoroughly at all times to ensure product consistency and consistent gloss.

Apply at 3-5 mils wet on sanded substrate. Further coats may be applied after complete drying followed by sanding with 280/320 grit stearated paper.

Maximum film build of Chemlack 550 White should not exceed 3 mils dry. Maximum film build of total coating system must not exceed 4 mils dry.

Chemlack 550 White should not be used and dried at temperatures below 64°F or relative humidity above 65%.

PDF Name: US-PIS_230-27XX_Chemlack_550_White_NC_Pigmented_TC

Tack Free Time: 10 minutes

Files: US-PIS_230-27XX_Chemlack_550_White_NC_Pigmented_TC.pdf

Dry to Sand : 30 - 45 minutes

Dry to Stack: 2 - 3 hours

Tack Free Time: Flash off before entering oven

VOC less exempt lb/gal: <4.55

Dry to Sand: 20 – 30 minutes

VOC lb/gal: <2.40

VOC less exempt g/l: <538

VOC g/l: <290

VOC lb/lb Solid: <0.87

Dry to Stack: 60 – 90 minutes

VHAPs lb/lb Solid: <0.25

Note: N/A

Note:

See individual compliance sheets for specific data

spec_description:

Chemlack 550 White is a single component nitrocellulose lacquer that provides good build and hide. Chemlack 550 White is a quality coating designed for the professional applicator that requires an easy to handle product. Chemlack 550 White is supplied at a ready to spray viscosity. This coating will dry quickly and sand easily.

Recommended: Architectural Woodwork Institute Nitrocellulose Lacquer System (8^th Ed).

spec_uses:

Chemlack 550 White is recommended for household furniture, millwork, decorative items as well as many other interior wood applications. Chemlack 550 White may be used for many interior wood applications.

Suggested Uses:

Wood Finish

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

Zahn #2 signature cup 20 – 25 seconds

Reducer: 800-5500

Retarder: 800-5742

Clean-up Solvent: 800-5500

Recommended Wet Film: 3 – 5 mils

Coverage:

Coverage is 275 sqft/gal at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness

Note application:

N/A

Viscosity:

Zahn #2 signature cup 25 sec at 77°F

Flash Point: -4°F (-20°C)

Density (lb/gal): 8.2

Solid (% by weight): 33%

Solid (% by volume): 19%

Shelf Life (months): 12

CHEMLACK WHITE Pigmented Topcoat

230-27XX Chemlack 550 White NC Pigmented TC

Find distributor Trouver un distributeur

spec_description:

Recommended: Architectural Woodwork Institute Nitrocellulose Lacquer System (8^th Ed).

BACK

CHEMLACK WHITE Pigmented Topcoat

230-27XX Chemlack 550 White NC Pigmented TC

spec_description:

Recommended: Architectural Woodwork Institute Nitrocellulose Lacquer System (8^th Ed).

Product codeCodes de produit
Product Codes:

230-2720 Low Gloss
230-2740 Satin
230-2760 Semi-Gloss
230-2780 High Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 25 sec at 77°F

Flash Point: -4°F (-20°C)

Density (lb/gal): 8.2

Solid (% by weight): 33%

Solid (% by volume): 19%

Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_230-27XX_Chemlack_550_White_NC_Pigmented_TC.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap