CHEMSEAL Sealer

546-1227 Chemseal 550 NC Clear Sealer

Product Codes:

546-1227

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit stearated paper prior to staining or coating. Chemseal 550 cannot be used on metal or old oil finishes. AkzoNobel recommends using 825-00XX or 825-09XX series stains or 824-50XX series waterborne stains.

General Information:

Agitate material before use. Chemseal 550 must be agitated thoroughly at all times to ensure product consistency.

Apply at 3-5 mils wet on sanded substrate. Further coats may be applied after complete drying followed by sanding with 280/320 grit stearated paper. Appropriate topcoat is Chemlack 550 441-27XX.

Maximum film build of Chemseal 550 should not exceed 2 mils dry. Maximum film build of total coating system must not exceed 3 mils dry.

Chemseal 550 should not be used and dried at temperatures below 64°F or relative humidity above 65%.

PDF Name: US-PIS_546-1227_Chemseal_550_NC_Clear_Sealer

Tack Free Time: 5 – 10 minutes

Files: US-PIS_546-1227_Chemseal_550_NC_Clear_Sealer.pdf

Dry to Sand : 10 – 20 minutes

Dry to Stack: 1 - 2 hours

Tack Free Time: Flash off before entering oven

VOC less exempt lb/gal: <4.50

Dry to Sand: 5 – 10 minutes

VOC lb/gal: <2.10

VOC less exempt g/l: <530

VOC g/l: <255

VOC lb/lb Solid: <1.20

Dry to Stack: 20 – 30 minutes

VHAPs lb/lb Solid: <0.3

Note: N/A

Note:

N/A

spec_description:

Chemseal 550 is a single component nitrocellulose sealer that provides excellent sealing properties and very rapid dry. Chemseal 550 is an easy sanding sealer designed for the professional applicator who requires a rapid dry, easy sanding material. All nitrocellulose lacquers will yellow over time. This could become an issue if this product is used over white surfaces. This yellowing generally adds a warm patina when applied over most other colors and stains.

Recommended: Architectural Woodwork Institute Nitrocellulose Lacquer System (8^th Ed).

spec_uses:

Chemseal 550 is recommended for household furniture, millwork, decorative items as well as many other interior wood applications.

Suggested Uses:

Wood Sealer

Mixing Ratio:

N/A

Pot Life:

N/A

Application Viscosity:

Zahn #2 signature cup 18 seconds

Reducer: 800-5500 for viscosity only

Retarder: 800-5742

Clean-up Solvent: 800-5500

Recommended Wet Film: 3 – 5 mils

Coverage:

Coverage is 265 sq. ft/gal at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

N/A

Viscosity:

Zahn #2 signature cup 18 sec at 77°F

Flash Point: -4°F (-20°C)

Density (lb/gal): 7.3

Solid (% by weight): 24%

Solid (% by volume): 16%

Shelf Life (months): 12

CHEMSEAL Sealer

546-1227 Chemseal 550 NC Clear Sealer

Find distributor Trouver un distributeur

spec_description:

Recommended: Architectural Woodwork Institute Nitrocellulose Lacquer System (8^th Ed).

BACK

CHEMSEAL Sealer

546-1227 Chemseal 550 NC Clear Sealer

spec_description:

Recommended: Architectural Woodwork Institute Nitrocellulose Lacquer System (8^th Ed).

Product codeCodes de produit
Product Codes:

546-1227

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 18 sec at 77°F

Flash Point: -4°F (-20°C)

Density (lb/gal): 7.3

Solid (% by weight): 24%

Solid (% by volume): 16%

Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_546-1227_Chemseal_550_NC_Clear_Sealer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap