Glaze
825-3680 Promatch® ProGlaze Neutral Wet Glaze
Product Codes:
825-3680
Surface Preparation:
N/A
General Information:
Prior to use, agitate thoroughly and tint as required with 844 line tints to a maximum of 25% by volume. The Promatch® ProGlaze Neutral Wet Glaze can be applied over washcoat, sealer, primer, enamel or topcoat. Must be re-coated with a clear topcoat afterwards. Sand with 280/320 grit paper before applying glaze. The glaze and topcoat must be applied within 8 hours of sanding.
Apply the Glaze by spraying or with a rag. Allow two or three minutes air drying before wiping. Wipe clean and do not leave on any excess material that may interfere with optimum adhesion.
Promatch® ProGlaze Neutral Wet Glaze must be thoroughly agitated to ensure product consistency.
Compatible with 436-48XX ora Verde® Chiaro, 431-46XX Varicure®, 131-53XX Varicure® Select, 421-63XX Chemlife® 24, 117-27XX Chemlife® 24 Plus, etc.
PDF Name: US-PIS_825-3680_Promatch_ProGlaze_Neutral_Wet_Glaze
Tack Free Time: N/A
Files: US-PIS_825-3680_Promatch_ProGlaze_Neutral_Wet_Glaze.pdf
Dry to Sand : N/A
Dry to Stack: N/A
Tack Free Time: N/A
VOC less exempt lb/gal: 5.1
Dry to Sand: N/A
VOC lb/gal: 5.1
VOC less exempt g/l: 612
VOC g/l: 612
VOC lb/lb Solid: 2.42
Dry to Stack: N/A
VHAPs lb/lb Solid: 0.03
Note: N/A
Note:
N/A
spec_description:
Promatch® ProGlaze Neutral Wet Glaze is an all-purpose wet glaze for furniture and cabinets. It is specially formulated to be used with 844 tints and can be tinted up to a maximum of 25% by volume. This universal solvent borne glaze provides good adhesion and workability with various technologies such as pre-cats, conversion varnishes and 2k polyurethane.
spec_uses:
Promatch® ProGlaze Neutral Wet Glaze is used for coloring of wood on furniture, cabinets and millwork. When properly applied, it will enhance the natural beauty of the wood.
Suggested Uses:
Wood Glaze
Mixing Ratio:
N/A
Pot Life: N/A
Application Viscosity:
N/A
Reducer: N/A
Retarder: N/A
Clean-up Solvent: 803-1298
Recommended Wet Film: N/A
Coverage:
N/A
Note application:
Applied spray or with rag, allow to dry, wipe or brush. Allow to dry.
Viscosity:
N/A
Flash Point: >200°F
Density (lb/gal): 7.19
Solid (% by weight): 29.2%
Solid (% by volume): 21.8%
Shelf Life (months): 24

Glaze

825-3680 Promatch® ProGlaze Neutral Wet Glaze

Find distributor Trouver un distributeur

spec_description:

Promatch® ProGlaze Neutral Wet Glaze is an all-purpose wet glaze for furniture and cabinets. It is specially formulated to be used with 844 tints and can be tinted up to a maximum of 25% by volume. This universal solvent borne glaze provides good adhesion and workability with various technologies such as pre-cats, conversion varnishes and 2k polyurethane.

BACKRetour

Product codeCodes de produit
Product Codes:

825-3680

Product information

Product specificationsSpécifications du produit

Viscosity:
N/A
Flash Point: >200°F
Density (lb/gal): 7.19
Solid (% by weight): 29.2%
Solid (% by volume): 21.8%
Shelf Life (months): 24

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_825-3680_Promatch_ProGlaze_Neutral_Wet_Glaze.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more