866 COLORANTS
827-1XXX 866 Colorants
Product Codes:
827-1202 Yellow Iron Oxide

827-1205 Titanium White

827-1206 Red Iron Oxide

827-1209 Burnt Sienna

827-1210 Phthalo Blue

827-1211 Raw Umber

827-1212 Burnt Umber

827-1217 Lamp Black

827-1219 Quinacridone Red

827-1223 Phthalo Green

827-1250 Lead Free Medium Orange

827-1462 Quinacridone Violet

827-1483 Organic Yellow LF
Surface Preparation:
N/A
General Information:
Follow recommendations found on Product Information Sheets of materials using this product. Different base materials will accept more or less of these colorants depending on use.

Proper handling is essential to maintain quality and consistency over time. Colorants must be mixed prior to use. Containers should be tightly sealed when not in use. If the colorant level is less than 20% of the package volume it is recommended to repack into smaller container if material is going to be stored for an extended period of time.

Refer to the Material Safety Data Sheet for important information on safety and handling for this material.

Vapor and liquid are irritating to skin and eyes. Wear goggles and gloves where there is danger of contact with the liquid.
PDF Name: US-PIS_827-1XXX_866_Colorants
Tack Free Time: N/A
Files: US-PIS_827-1XXX_866_Colorants.pdf
Dry to Sand : N/A
Dry to Stack: N/A
Tack Free Time: N/A
VOC less exempt lb/gal: N/A
Dry to Sand: N/A
VOC lb/gal: N/A
VOC less exempt g/l: N/A
VOC g/l: N/A
VOC lb/lb Solid: N/A
Dry to Stack: N/A
VHAPs lb/lb Solid: N/A
Note: N/A
Note:
N/A
spec_description:
866 Colorants are medium-oil alkyd based tints designed for use in solvent-borne industrial coatings. They are widely compatible and available in a broad spectrum of colors.

Note: Shelf life is 24 months if unopened
spec_uses:
This product line is designed as a colorant for solvent-borne coatings and stains.
Suggested Uses:
Tinter
Mixing Ratio:
See individual product sheets
Pot Life:
N/A
Application Viscosity:
See individual product sheets
Reducer: N/A
Retarder: N/A
Clean-up Solvent: 803-1298
Recommended Wet Film: N/A
Coverage:
N/A
Note application:
N/A
Viscosity:
N/A
Flash Point: 82F (28C)
Density (lb/gal): Varies (9-15)
Solid (% by weight): Varies (72-86)
Solid (% by volume): Varies (63-68)
Shelf Life (months): 24

866 COLORANTS

827-1XXX 866 Colorants

Find distributor Trouver un distributeur

spec_description:

866 Colorants are medium-oil alkyd based tints designed for use in solvent-borne industrial coatings. They are widely compatible and available in a broad spectrum of colors.

Note: Shelf life is 24 months if unopened

BACKRetour

Product codeCodes de produit
Product Codes:

827-1202 Yellow Iron Oxide

827-1205 Titanium White

827-1206 Red Iron Oxide

827-1209 Burnt Sienna

827-1210 Phthalo Blue

827-1211 Raw Umber

827-1212 Burnt Umber

827-1217 Lamp Black

827-1219 Quinacridone Red

827-1223 Phthalo Green

827-1250 Lead Free Medium Orange

827-1462 Quinacridone Violet

827-1483 Organic Yellow LF

Product information

Product specificationsSpécifications du produit

Viscosity:
N/A
Flash Point: 82F (28C)
Density (lb/gal): Varies (9-15)
Solid (% by weight): Varies (72-86)
Solid (% by volume): Varies (63-68)
Shelf Life (months): 24

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_827-1XXX_866_Colorants.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more