CHEMSEAL Sealer
546-1201 Chemseal NC Clear Sealer
Product Codes:
546-1201
Surface Preparation:
Substrate must be sanded using 120, 150 or 180 grit stearated paper prior to staining or coating. Sealers should be sanded with 280/320 grit stearated paper prior to being coated.
General Information:
Chemseal 546-1201 is applied in two or more coats; however, the dry film build should not exceed 1 – 2 mils. The dry film build of the total system should not exceed 4 mils. Chemseal 546-1201 should be thoroughly stirred and mixed with an appropriate amount of reducer.

Chemseal 546-1201 does contain zinc stearated and should not be recoated with reactive amino coatings.
PDF Name: US-PIS_546-1201_Chemseal_NC_Clear_Sealer
Tack Free Time: 10 – 15 minutes
Files: US-PIS_546-1201_Chemseal_NC_Clear_Sealer.pdf
Dry to Sand : 30 - 45 minutes
Dry to Stack: 1 - 2 hours
Tack Free Time: Flash off before entering oven
VOC less exempt lb/gal: <5.80
Dry to Sand: 15 – 20 minutes
VOC lb/gal: <5.40
VOC less exempt g/l: <700
VOC g/l: <650
VOC lb/lb Solid: <4.2
Dry to Stack: 20 – 30 minutes
VHAPs lb/lb Solid: <0.8
Note: N/A
Note:
N/A
spec_description:
Chemseal is a ready to use, nitrocellulose lacquer sealer. It is a single pack, conventional lacquer sealer. Chemseal dries rapidly, powders well, and seals the substrate preparing it for the appropriate topcoat.
spec_uses:
Various interior wood applications.
Suggested Uses:
Wood Sealer
Mixing Ratio:
N/A
Pot Life:
N/A
Application Viscosity:
Zahn #2 signature cup 20 – 25 seconds
Reducer: 803-1395
Retarder: 803-1393 or 800-5328
Clean-up Solvent: 803-1395
Recommended Wet Film: 2 – 5 mils
Coverage:
208 sq. ft/gal at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.
Note application:
N/A
Viscosity:
Zahn #2 signature cup 25 sec at 77°F
Flash Point: -4°F (-20°C)
Density (lb/gal): 7.1
Solid (% by weight): 18%
Solid (% by volume): 12%
Shelf Life (months): 12

CHEMSEAL Sealer

546-1201 Chemseal NC Clear Sealer

Find distributor Trouver un distributeur

spec_description:

Chemseal is a ready to use, nitrocellulose lacquer sealer. It is a single pack, conventional lacquer sealer. Chemseal dries rapidly, powders well, and seals the substrate preparing it for the appropriate topcoat.

BACKRetour

Product codeCodes de produit
Product Codes:

546-1201

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #2 signature cup 25 sec at 77°F
Flash Point: -4°F (-20°C)
Density (lb/gal): 7.1
Solid (% by weight): 18%
Solid (% by volume): 12%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_546-1201_Chemseal_NC_Clear_Sealer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more