Selva Pro
420-1205 Selva Pro™ Isolante Sealer
Product Codes:
420-1205
Surface Preparation:
Wood must be sanded with a 120 or 150 grit paper and free of dust and all contaminants.
General Information:
Apply 3 to 5 wet mils on a sanded surface. Let dry for 30 to 60 minutes and apply the desired topcoat. If the drying time exceeds 4 hours, sanding is required to keep a good adhesion. Once catalyzed with 876-9084, this product will contain isocyanates. Take necessary precautions for the handling and use of this product. See MSDS. AkzoNobel recommends using Promatch W/B Monocolor Spray Stains 824-50XX, Promatch Aqua Stains 824-51XX, Promatch Dye Stains 890-85XX, Promatch Vivid Wipe Stains 8255600, Promatch C-Mix Wipe Stains 825-90XX, 825-91XX.
For a complete system cure, the system must be applied at a temperature above 18ºC and relative humidity below 65%.
Complete system must be verified and approved by AkzoNobel before going on production.
PDF Name: US-PIS_420-1205_Isolante_Sealer
Tack Free Time: 30-60 minutes
Files: US-PIS_420-1205_Isolante_Sealer.pdf
Dry to Sand : 4 hours
Dry to Stack: N/A
Tack Free Time: 15-20 minutes
VOC less exempt lb/gal: 5.83
Dry to Sand: 30 minutes
VOC lb/gal: 5.83
VOC less exempt g/l: 698
VOC g/l: 698
VOC lb/lb Solid: 3.38
Dry to Stack: N/A
VHAPs lb/lb Solid: 0.84
Note: N/A
Note:
N/A
spec_description:
Selva Pro Isolante 2K Sealer is designed to enhance adhesion on exotic or oily substrates. Its features include strong bond, barrior coat properties and ease of sandability, making it ideal for high-end wood applications.
spec_uses:
Used as a barrior coat on exotic substrates and/or as an adhesion promoter under any Selva Pro sealers or Chemcraft's polyester sealer.
Suggested Uses: Wood Finishes
Mixing Ratio:
100 Parts 420-1205 with 50 Parts 876-9084 (by volume)
Pot Life: 4 hours
Application Viscosity:
20-22 sec Zahn #2 at 77° F (25°C)
Reducer: 803-2000
Retarder: N/A
Clean-up Solvent: 800-5500 Acetone
Recommended Wet Film: 3-5 wet mils
Coverage:
N/A
Note application:
N/A
Viscosity:
27-29 sec Zahn #2 at 77° F (25°C)
Flash Point: 21.2° F (9° C)
Density (lb/gal): 7.64
Solid (% by weight): 22.8
Solid (% by volume): 15.2
Shelf Life (months): 24

Selva Pro

420-1205 Selva Pro™ Isolante Sealer

Find distributor Trouver un distributeur

spec_description:

Selva Pro Isolante 2K Sealer is designed to enhance adhesion on exotic or oily substrates. Its features include strong bond, barrior coat properties and ease of sandability, making it ideal for high-end wood applications.

BACKRetour

Product codeCodes de produit
Product Codes:

420-1205

Product information

Product specificationsSpécifications du produit

Viscosity:
27-29 sec Zahn #2 at 77° F (25°C)
Flash Point: 21.2° F (9° C)
Density (lb/gal): 7.64
Solid (% by weight): 22.8
Solid (% by volume): 15.2
Shelf Life (months): 24

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_420-1205_Isolante_Sealer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more