VERDE POLIESTERE Sealer
458-1288 Reslack Polyester Clear Sealer
Product Codes:
458-1288
Surface Preparation:
Apply to MDF after sanding substrate with 120/150 grit paper. To obtain maximum adhesion over MDF and for use over wood, application of the urethane washcoat is required. After curing, the washcoat should be sanded with 240 grit paper.
General Information:
Agitate material before use and while adding accelerator and/or hardener per mixing ratio. To ensure product consistency, the mixed material should be agitated at all times. Times between coats for wet on wet spray are about 20 minutes so the sealer will gel in order to give good intercoat adhesion. The topcoat must be applied within 8 hours following sanding of 458-1288 Reslack Sealer Thix. It may be overcoated with ora Verde Chiaro 436-48XX, ora Verde Acrilico 436-38XX or Reslack Clear 458-1290.

With profiled doors, care must be taken with sanding of the primer to avoid sanding through on sharp edges. Complex profiles or profiles with sharp corners may cause difficulties in obtaining an effective prime coat of even film thickness. In these cases, profile design must be discussed with your technical representative. Maximum film build of 458-1288 should not exceed 20 mils dry.
PDF Name: US-PIS_458-1288_Reslack_Polyester_Clear_Sealer
Tack Free Time: 1 hour
Files: US-PIS_458-1288_Reslack_Polyester_Clear_Sealer.pdf
Dry to Sand : 4 hours
Dry to Stack: Overnight
Tack Free Time: 20 – 30 minutes
VOC less exempt lb/gal: <5.0
Dry to Sand: 1 – 2 hours
VOC lb/gal: <5.0
VOC less exempt g/l: <600
VOC g/l: <600
VOC lb/lb Solid: <1.35
Dry to Stack: 4 – 6 hours
VHAPs lb/lb Solid: <0.13 per 40 CFR §63.803(1)(2)
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
Reslack Sealer Thix is a thixotropic polyester sealer for application when excellent build is required for sealing wood and wood products for interior use. It is based on wax-free polyester resins and provides exceptional filling properties, good flexibility, and excellent sanding.
spec_uses:
458-1288 is used as a sealer for all types of closed grain finishes and is especially recommended for surfaces where it is difficult to perform a proper sanding.
Suggested Uses:
Wood Sealer
Mixing Ratio:
When used as a one-component, mix 100 parts by volume of 458-1288 Reslack Sealer Thix with 2.0 parts by volume of each 881-1202 accelerator and 872-1202 hardener. Note: The accelerator and the Hardener must never come in contact with each other. Add accelerator and stir well, then add hardener and stir well. When used as a two-component, first container mix 100 parts by volume of 458-1288 and 4.0 parts by volume 872-1202 hardener, second container mix 100 parts by volume 458-1288 and 4.0 parts by volume of 881-1202 accelerator. Adjust mixing ratio between containers 1:1
Pot Life:
5-10 mins. Used as a 2 Component 6 hours per side at 68°F
Application Viscosity:
Zahn #3 28 seconds
Reducer: 800-5302 or 800-5500 (maximum 5% by volume)
Retarder: N/A
Clean-up Solvent: 800-5500
Recommended Wet Film: 8 – 10 mils
Coverage:
N/A
Note application:
N/A
Viscosity:
Zahn #3 signature cup 28 sec at 77°F
Flash Point: -40°F (4°C)
Density (lb/gal): 8.7
Solid (% by weight): 97% (reactive)
Solid (% by volume): 97% (reactive)
Shelf Life (months): 3

VERDE POLIESTERE Sealer

458-1288 Reslack Polyester Clear Sealer

Find distributor Trouver un distributeur

spec_description:

Reslack Sealer Thix is a thixotropic polyester sealer for application when excellent build is required for sealing wood and wood products for interior use. It is based on wax-free polyester resins and provides exceptional filling properties, good flexibility, and excellent sanding.

BACKRetour

Product codeCodes de produit
Product Codes:

458-1288

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #3 signature cup 28 sec at 77°F
Flash Point: -40°F (4°C)
Density (lb/gal): 8.7
Solid (% by weight): 97% (reactive)
Solid (% by volume): 97% (reactive)
Shelf Life (months): 3

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_458-1288_Reslack_Polyester_Clear_Sealer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more