CHEMLIFE 24 WHITE Pigmented Topcoat
117-24XX Chemlife® 24 White Conversion Varnish Pigmented TC
Product Codes:
117-2410 Matte
117-2420 Low Gloss
117-2435 Satin
117-2450 Semi-Gloss
117-2490 High Gloss
Surface Preparation:
Primer should be sanded using 240 and 320 grit stearated paper. Suitable primer is Chemlife 24 White Primer 522-2400. The primer should be topcoated within eight hours of sanding. Care should be taken during sanding to avoid sanding through the primer.
General Information:
Catalyze and reduce the material as recommended. Chemlife 24 White is applied in one or two coats and can be used on all kinds of wood meant for interior use.

A thorough sanding between the coats is essential to the adhesion. The second and subsequent coats must be applied the same day as the previous coat is sanded. Chemlife 24 White cannot be used on metal, old oil or cellulose lacquers.

Total recommended film build of Chemlife 24 White Primer 522-2400 and Chemlife 24 White 117-24XX is not to exceed 6 mils dry. Over the primer, the topcoat should not exceed 4 mils dry.

To ensure proper sheen, the catalyzed material should be agitated at all times. Chemlife 24 White must be thoroughly stirred while adding catalyst and thinner in the recommended mixing ratio. Contact with metal surfaces should be avoided once the Chemlife 24 White has been catalyzed.

Chemlife 24 White must not be polluted with oil, varnish or the like and must not be sanded with steel wool between coats. Chemlife 24 White must not be used and dried at temperatures below 65°F (18°C) or relative humidity above 65%. During the curing process, the coating must not be exposed to ammonia vapors. Ammonia cleaners should not be used for cleaning the finished surface. This may accelerate discoloration.
PDF Name: US-PIS_117-24XX_Chemlife_24_White_Conversion_Varnish_Pigmented_TC
Tack Free Time: 15 – 20 minutes
Files: US-PIS_117-24XX_Chemlife_24_White_Conversion_Varnish_Pigmented_TC.pdf
Dry to Sand : 3 hours
Dry to Stack: Overnight
Tack Free Time: Flash off before entering oven
VOC less exempt lb/gal: <3.90
Dry to Sand: 1 hour
VOC lb/gal: <3.90
VOC less exempt g/l: <468
VOC g/l: <468
VOC lb/lb Solid: <0.75
Dry to Stack: 3 hours
VHAPs lb/lb Solid: <0.30
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
Chemlife 24 White is an acid curing, light stable, fast drying Reactive Amino Coating (RAC) with good building properties. It gives a smooth, knock-proof and hardwearing surface resisting influence from alcohol, water, etc. Due to its 24 hour pot-life, Chemlife 24 White provides the customer with minimum waste resulting in lower production costs. It also provides very good light stability based on the type of resin used and superior vertical hang.

Special Recognition: When applied as specified, will meet required performance for the ANSI/KCMA A161.1 1990 9.0 Finish Test. Recommended: Architectural Woodwork Institute (AWI) O.P.4.
spec_uses:
This product is used as the final coat over wood, plywood, chipboard, etc., meant for interior use. This product is recommended for kitchen cabinets, high build office or residential furniture as well as many other interior wood applications where high build and durability are required.
Suggested Uses:
Wood Finish
Mixing Ratio:
100 parts 117-24XX to 10 part 873-1251
Pot Life:
24 hours
Application Viscosity:
Zahn #2 signature cup 22 – 25 seconds
Reducer: 803-1325
Retarder: 800-5328
Clean-up Solvent: 803-1298
Recommended Wet Film: 4-5 mils
Coverage:
698 sq. ft/gal at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.
Note application:
N/A
Viscosity:
Zahn #3 signature cup 24 sec at 77°F
Flash Point: 55°F (12.8°C)
Density (lb/gal): 9.42
Solid (% by weight): 58.6%
Solid (% by volume): 43.5%
Shelf Life (months): 12

CHEMLIFE 24 WHITE Pigmented Topcoat

117-24XX Chemlife® 24 White Conversion Varnish Pigmented TC

Find distributor Trouver un distributeur

spec_description:

Chemlife 24 White is an acid curing, light stable, fast drying Reactive Amino Coating (RAC) with good building properties. It gives a smooth, knock-proof and hardwearing surface resisting influence from alcohol, water, etc. Due to its 24 hour pot-life, Chemlife 24 White provides the customer with minimum waste resulting in lower production costs. It also provides very good light stability based on the type of resin used and superior vertical hang.

Special Recognition: When applied as specified, will meet required performance for the ANSI/KCMA A161.1 1990 9.0 Finish Test. Recommended: Architectural Woodwork Institute (AWI) O.P.4.

BACKRetour

Product codeCodes de produit
Product Codes:

117-2410 Matte
117-2420 Low Gloss
117-2435 Satin
117-2450 Semi-Gloss
117-2490 High Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #3 signature cup 24 sec at 77°F
Flash Point: 55°F (12.8°C)
Density (lb/gal): 9.42
Solid (% by weight): 58.6%
Solid (% by volume): 43.5%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_117-24XX_Chemlife_24_White_Conversion_Varnish_Pigmented_TC.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more