DANSEAL Sealer
432-1220 Danseal Post-Cat Clear Sealer
Product Codes:
432-1220
Surface Preparation:
Substrate must be sanded using 120, 150 or 180 grit stearated paper prior to staining or coating. Sealers should be sanded with 240, 280 and 320 grit stearated paper prior to being coated. Stain systems used under acid catalyzed systems should be acid stable. AkzoNobel recommends 825-90XX, 825-91XX Promatch® C-Mix Stains, or 890-85XX Promatch Dye Stains. Danseal cannot be used on metal, old oil or cellulose lacquers.
General Information:
Agitate material thoroughly before use. Always mix Danseal while adding catalyst in the recommended mixing ratios. Apply and allow to dry for one hour. Scuff sand with 220 to 280 grit stearated paper before topcoating to ensure good adhesion and a smooth finish. The second and subsequent coats must be applied the same day as the previous coat is sanded.

Danseal must not be used and dried at temperatures below 64°F or relative humidity above 65%. During the curing process, the coating must not be exposed to ammonia vapors. Ammonia cleaners should not be used for cleaning the finished surface. This may accelerate discoloration.

Maximum film build of Danseal should not exceed 2 mils dry. Maximum film build of total coating system must not exceed 4 mils dry.

Contact with metal surfaces should be avoided.
PDF Name: US-PIS_432-1220_Danseal_Post-Cat_Clear_Sealer
Tack Free Time: 15 – 20 minutes
Files: US-PIS_432-1220_Danseal_Post-Cat_Clear_Sealer.pdf
Dry to Sand : 1 hour
Dry to Stack: 8 hours
Tack Free Time: Flash off before entering oven
VOC less exempt lb/gal: <5.20
Dry to Sand: 20 – 30 minutes
VOC lb/gal: <4.47
VOC less exempt g/l: <625
VOC g/l: <540
VOC lb/lb Solid: <1.85
Dry to Stack: 40 – 45 minutes
VHAPs lb/lb Solid: <0.7
Note: N/A
Note:
N/A
spec_description:
Danseal is a high solids modified Reactive Amino Coating (RAC). Danseal provides good clarity, fast dry and excellent sanding characteristics.
spec_uses:
Danseal is specifically made for use under Danspeed 424-45XX, Danspeed Elite 424-44XX, Plastofix Light 421-48XX and E-Var 421-80XX.
Suggested Uses:
Wood Sealer
Mixing Ratio:
100 parts 432-1220 to 7 parts 873-0870
Pot Life:
12 hours
Application Viscosity:
Zahn #2 signature cup 20 – 24 seconds
Reducer: 803-1325
Retarder: 800-5328
Clean-up Solvent: 803-1298
Recommended Wet Film: 3 – 5 mils
Coverage:
385 sq. ft/gal at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.
Note application:
N/A
Viscosity:
Zahn #2 signature cup 24 sec at 77°F
Flash Point: 24°F (-4°C)
Density (lb/gal): 7.8
Solid (% by weight): 31%
Solid (% by volume): 23%
Shelf Life (months): 12

DANSEAL Sealer

432-1220 Danseal Post-Cat Clear Sealer

Find distributor Trouver un distributeur

spec_description:

Danseal is a high solids modified Reactive Amino Coating (RAC). Danseal provides good clarity, fast dry and excellent sanding characteristics.

BACKRetour

Product codeCodes de produit
Product Codes:

432-1220

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #2 signature cup 24 sec at 77°F
Flash Point: 24°F (-4°C)
Density (lb/gal): 7.8
Solid (% by weight): 31%
Solid (% by volume): 23%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_432-1220_Danseal_Post-Cat_Clear_Sealer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more