Variset Select Primer
545-5201 Variset® Select Neutral Pre-Cat Pigmented Vinyl Primer
Product Codes:
545-5201
Surface Preparation:
Substrate should be sanded using 120, 150 or 180 grit stearated paper prior to coating. Variset Select Neutral Vinyl Primer should be sanded with 280/320 grit stearated paper prior to being coated and the next coat must be applied within eight hours of sanding. Variset Select Neutral Vinyl Primer cannot be used on metal, old oil or cellulose lacquers.
General Information:
Agitate material before use. Always mix Variset Select Neutral Vinyl Primer while adding reducers in the recommended mixing ratio. Variset Select Neutral Vinyl Primer must be agitated thoroughly at all times to ensure product consistency.
Apply at 3 - 5 mils wet to sanded substrate. Further coats may be applied after complete drying followed by sanding with 280/320 grit stearated paper.
Maximum film build of Variset Select Neutral Vinyl Primer should not exceed 2 - 3 mils dry. Maximum film build of total coating system must not exceed 4 mils dry. Contact with metal surfaces should be avoided.
Variset Select Neutral Vinyl Primer must not be polluted with oil, varnish or the like and must not be sanded with steel wool between coats.
Variset Select Neutral Vinyl Primer must not be used and dried at temperatures below 64°F or relative humidity above 65%. During the curing process, the coating must not be exposed to ammonia vapors. Ammonia cleaners should not be used for cleaning the finish surfaces. This may accelerate discoloration.
PDF Name: US-PIS_545-5201_Variset_Select_Neutral_Pre-Cat_Pigmented_Vinyl_Primer
Tack Free Time: 10 - 20 minutes
Files: US-PIS_545-5201_Variset_Select_Neutral_Pre-Cat_Pigmented_Vinyl_Primer.pdf
Dry to Sand : 60 - 75 minutes
Dry to Stack: 3 hours
Tack Free Time: Flash off before entering oven
VOC less exempt lb/gal: <4.81
Dry to Sand: 20 - 30 minutes
VOC lb/gal: <4.17
VOC less exempt g/l: <570
VOC g/l: <500
VOC lb/lb Solid: <1.05
Dry to Stack: 60 - 90 minutes
VHAPs lb/lb Solid: <0.31
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
Variset Select Neutral Vinyl Primer is a one-component, high solids, pre-catalyzed wood coating and has excellent hiding and filling properties. It is easy to use, sands quickly and easily and has superior moisture resistance. It has excellent adhesion and outstanding vertical hang / sag resistance.
Variset Select Neutral Vinyl Primer comes in a ready to use format, there is no need for reduction. This pigmented pre-catalyzed wood coating has very low odor during the curing process.
spec_uses:
Variset Select Neutral Vinyl Primer is recommended for use as a primer for Variset Select Topcoat. It has good filling properties and hiding characteristics.
Suggested Uses:
Wood Primer
Mixing Ratio:
N/A
Pot Life: N/A
Application Viscosity:
Zahn #2 signature cup 27 - 29 seconds
Reducer: 803-1325
Retarder: 800-5328
Clean-up Solvent: 803-1298
Recommended Wet Film: 5 mils
Coverage:
434 sq. ft. / gal at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.
Note application:
N/A
Viscosity:
Zahn #2 signature cup 27 sec at 77°F
Flash Point: -4°F (-20°C)
Density (lb/gal): 9.03
Solid (% by weight): 44.1%
Solid (% by volume): 27.06%
Shelf Life (months): 12

Variset Select Primer

545-5201 Variset® Select Neutral Pre-Cat Pigmented Vinyl Primer

Find distributor Trouver un distributeur

spec_description:

Variset Select Neutral Vinyl Primer is a one-component, high solids, pre-catalyzed wood coating and has excellent hiding and filling properties. It is easy to use, sands quickly and easily and has superior moisture resistance. It has excellent adhesion and outstanding vertical hang / sag resistance.
Variset Select Neutral Vinyl Primer comes in a ready to use format, there is no need for reduction. This pigmented pre-catalyzed wood coating has very low odor during the curing process.

BACKRetour

Product codeCodes de produit
Product Codes:

545-5201

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #2 signature cup 27 sec at 77°F
Flash Point: -4°F (-20°C)
Density (lb/gal): 9.03
Solid (% by weight): 44.1%
Solid (% by volume): 27.06%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_545-5201_Variset_Select_Neutral_Pre-Cat_Pigmented_Vinyl_Primer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more