AQUALUX UNICLEAR Topcoat
423-46XX Aqualux® Uniclear WB Clear TC
Product Codes:
423-4610 Matte
423-4620 Low Gloss
423-4635 Satin
423-4650 Semi-Gloss
Surface Preparation:
Substrate should be sanded using 120, 150 or 180 grit sandpaper prior to staining or coating. Sealers if used should be sanded with 240, 280, and 320 grit stearated paper prior to being coated. Stain systems recommended under this product are Promatch® Aqua Wiping Stains 824-50XX, 824-51XX, 824-8012, 824-8019, Promatch C-Mix Wiping Stains 825-90XX, 825-91XX, Promatch Dye Stains 890-85XX or Promatch Aqua Dye Stains 890-12XX.
General Information:
Mix material before use. Add water to reduce, if required, and mix thoroughly. Apply by spray at wet film builds of 4 - 5 mils. Application and drying conditions must be at temperatures of 64°F or above and at a humidity of less than 65%. Increased airflow and/or drying temperatures, including the use of infrared, will greatly decrease dry times.
Apply at 4 - 5 mils wet on sanded or sealed substrate. Further coats may be applied after complete drying followed by sanding with 280/320 grit stearated paper. Second and subsequent coats must be applied the same day the previous coat is sanded.
Aqualux Uniclear must be agitated thoroughly at all times to ensure product consistency. Contact with metal surfaces should be avoided. In the curing cycle, the addition of heat and air movement will shorten the drying time.
Note: Aqualux Uniclear must not be polluted with oil, solvent based paint or the like and should not be applied to metal surfaces. Aqualux Uniclear must not be sanded with steel wool between the coats. This coating must not be used and dried at temperatures below 64°F or relative humidity above 65%.
Film build should not exceed 2 dry mils per coat. Total film build must not exceed 4 dry mils.
PDF Name: US-PIS_423-46XX_Aqualux®_Uniclear_WB_Clear_TC
Tack Free Time: 15-20 minutes
Files: US-PIS_423-46XX_Aqualux®_Uniclear_WB_Clear_TC.pdf
Dry to Sand : 1 hour
Dry to Stack: 8 hours
Tack Free Time: 10-15 minutes
VOC less exempt lb/gal: <2.2
Dry to Sand: 45 minutes
VOC lb/gal: <0.8
VOC less exempt g/l: <260
VOC g/l: <100
VOC lb/lb Solid: <0.31
Dry to Stack: 6 hours
VHAPs lb/lb Solid: <0.1
Note: N/A
Note:
N/A
spec_description:
Aqualux Uniclear Topcoat is an extremely durable acrylic with superior mar resistance. Aqualux Uniclear Topcoat is a water white resin system with excellent chemical resistance. Aqualux Uniclear Topcoat offers hardness, clarity, soft feel and excellent surface slip.
It's low V.O.C. content and no formaldehyde allows it to qualify for LEED Projects.
Special Recognition: Meets Kitchen Cabinet Manufacturer Association (KCMA) Standards.
Recommended: Architectural Woodwork Institute. (AWI). T.R.3.
spec_uses:
Aqualux Uniclear Topcoat is designed for interior furniture, fittings, kitchen cabinet and other wood applications.
Suggested Uses:
Wood Finish
Mixing Ratio:
N/A
Pot Life:
N/A
Application Viscosity:
Zahn #3 signature cup 35 seconds
Reducer: Water as required
Retarder: N/A
Clean-up Solvent: Use water when in liquid state, use water / Butyl Cellosolve 800-5742 when material is semi-dried
Recommended Wet Film: 4 - 5 wet mils
Coverage:
450 sq. ft/gal at 1 mil dry and at 100% transfer efficiency. Coverage will vary depending on method of application or coating thickness.
Note application:
N/A
Viscosity:
Zahn #3 signature cup 35 sec at 77°F
Flash Point: >180° F
Density (lb/gal): 8.59
Solid (% by weight): 30.4%
Solid (% by volume): 28.0%
Shelf Life (months): 12

AQUALUX UNICLEAR Topcoat

423-46XX Aqualux® Uniclear WB Clear TC

Find distributor Trouver un distributeur

spec_description:

Aqualux Uniclear Topcoat is an extremely durable acrylic with superior mar resistance. Aqualux Uniclear Topcoat is a water white resin system with excellent chemical resistance. Aqualux Uniclear Topcoat offers hardness, clarity, soft feel and excellent surface slip.

It's low V.O.C. content and no formaldehyde allows it to qualify for LEED Projects.

Special Recognition: Meets Kitchen Cabinet Manufacturer Association (KCMA) Standards.

Recommended: Architectural Woodwork Institute. (AWI). T.R.3.

BACKRetour

Product codeCodes de produit
Product Codes:

423-4610 Matte
423-4620 Low Gloss
423-4635 Satin
423-4650 Semi-Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #3 signature cup 35 sec at 77°F
Flash Point: >180° F
Density (lb/gal): 8.59
Solid (% by weight): 30.4%
Solid (% by volume): 28.0%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_423-46XX_Aqualux®_Uniclear_WB_Clear_TC.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more