Aquaprime
550-1611 WB White Stainblock Primer
Product Codes:
550-1611
Surface Preparation: Substrate must be sanded using 120, 150 or 180 grit paper prior to coating. WB White Stainblock Primer should be sanded with 280/320 grit paper prior to being coated. WB White Stainblock Prime should be coated within (8) hours of being sanded for maximum adhesion. When recoating, the previous coat of WB White Stainblock Primer must be sanded and the next coat applied within (8) hours.
General Information:
Mix material before use. Add water to reduce if required and mix thoroughly. Apply by spray at 4 - 5 mils wet.

WB White Stainblock Primer must be agitated thoroughly at all times to ensure product consistency. Contact with metal surfaces should be avoided.

Maximum film build of total coating system must not exceed 4 mils dry.
PDF Name: US-PIS_550-1611_WB_White_Stainblock_Primer
Tack Free Time: 15 minutes
Files: US-PIS_550-1611_WB_White_Stainblock_Primer.pdf
Dry to Sand : 45 minutes
Dry to Stack: 24 hours
Tack Free Time: 15 minutes @ room temperature
VOC less exempt lb/gal: <0.49
Dry to Sand: 15 minutes @ 110° F
VOC lb/gal: <0.25
VOC less exempt g/l: <58
VOC g/l: <30
VOC lb/lb Solid: <1.03
Dry to Stack: 15 minutes @ 140° F
VHAPs lb/lb Solid: <0.01
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
WB White Stainblock Primer is a ready to use white waterborne primer. WB White Stainblock Primer provides very good hiding when used as a primer only on hardwoods or MDF. WB White Stainblock Primer offers excellent filling capabilities due to its high solid content at application (47% by volume). WB White Stainblock Primer provides an excellent base and is extreamely easy to sand. After sanding it may be topcoated with any of the Chemcrat topcoats from waterborne, pre-catalyzed lacquer, post-catalyzed lacquer, varish and urethane.
spec_uses:
This product is designed for hardwoods or MDF. It is formulated especially for windows and door frames, joinery pieces, and cabinets. Excellent primer for pre-primed jobs only.
Suggested Uses:
Wood Primer
Mixing Ratio:
N/A
Pot Life:
N/A
Application Viscosity:
Zahn #2 signature cup 25-30 seconds
Reducer: Use water as required. This product requires very little water to lower the viscosity.
Retarder: N/A
Clean-up Solvent: Use water when in liquid state, use water / Butyl Cellosolve 800-5742 when material is semi-dried
Recommended Wet Film: 4 - 5 mils wet
Coverage:
N/A
Note application:
N/A
Viscosity:
Zahn #2 signature cup 25-30 sec at 77°F
Flash Point: >200° F
Density (lb/gal): 12.55
Solid (% by weight): 65%
Solid (% by volume): 47%
Shelf Life (months): 6

Aquaprime

550-1611 WB White Stainblock Primer

Find distributor Trouver un distributeur

spec_description:

WB White Stainblock Primer is a ready to use white waterborne primer. WB White Stainblock Primer provides very good hiding when used as a primer only on hardwoods or MDF. WB White Stainblock Primer offers excellent filling capabilities due to its high solid content at application (47% by volume). WB White Stainblock Primer provides an excellent base and is extreamely easy to sand. After sanding it may be topcoated with any of the Chemcrat topcoats from waterborne, pre-catalyzed lacquer, post-catalyzed lacquer, varish and urethane.

BACKRetour

Product codeCodes de produit
Product Codes:

550-1611

Product information

Product specificationsSpécifications du produit

Viscosity:
Zahn #2 signature cup 25-30 sec at 77°F
Flash Point: >200° F
Density (lb/gal): 12.55
Solid (% by weight): 65%
Solid (% by volume): 47%
Shelf Life (months): 6

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_550-1611_WB_White_Stainblock_Primer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more