Waterborne 1K
AQUASILK 200TW 1K WHITE 228-24XX
Product Codes:
228-2405 FLAT,
228-2410 MATTE,
228-2420 LOW GLOSS,
228-2435 SATIN,
228-2450 SEMI-GLOSS,
228-2490 HIGH GLOSS
Surface Preparation: Substrate must be sanded using 120, 150 or 180 grit paper prior to prime. Primer should be sanded with 280/320 grit paper prior to being coated. Primer should be coated within eight hours of sanding. Appropriate primers are the Chemcraft 550-3500, 550-3501, 550-3502, 550-1600, 550-1602, 550-1760, and 550-1761. Always recoat within eight hours of sanding.
General Information:
N/A
PDF Name: US-PIS_AQUASILK_200TW_1K_WHITE_228-24XX
Tack Free Time: 30 minutes
Files: US-PIS_AQUASILK_200TW_1K_WHITE_228-24XX.pdf
Dry to Sand : 15 minutes
Dry to Stack: 24 hours
Tack Free Time: 15 minutes
VOC less exempt lb/gal: 1,80
Dry to Sand: 30 minutes
VOC lb/gal: 0,800
VOC less exempt g/l: 215
VOC g/l: 096
VOC lb/lb Solid: 0,18
Dry to Stack: 60 minutes
VHAPs lb/lb Solid: 0,00
Note: N/A
Note:
N/A
spec_description:
AQUASILK 200TW 1K White Topcoat is an acrylic selfcrosslinking product that is utilized in various markets. It meets AWI system #7 and specific KCMA requirements.

AQUASILK 200TW 1K White Topcoat has unique thixotropy for vertical and horizontal application. It has excellent hiding properties.

Waterborne MaestroHue complete color sytem available utilizing 897 colorants at a maximum 7%.
spec_uses:
AQUASILK 200TW 1K White Topcoat is designed for cabinets, architectural millwork, furniture and refinish markets.
Suggested Uses:
For cabinets, Architectural millwork, furniture, and refinish mar
Mixing Ratio:
N/A
Pot Life:
N/A
Application Viscosity:
40 - 45 seconds Zahn signature #4
Reducer: Water up to 10% by volume depending on spray equipment
Retarder: 803-1462 1 to 3% by volume as needed
Clean-up Solvent: Water
Recommended Wet Film: 4 - 6 wet mils
Coverage:
589 sqft/gal
Note application:
Depending on spray equipment the AQUASILK 200TW 1K White Topcoat may need some reduction, the addition up to 10% water is recommended for cup gun, gravity cup or HVLP.

For Air Assisted Airless AQUASILK 200TW 1K White Topcoat can be used as it is.
Viscosity:
900 - 1100 cP at 77°F (25°C)
Flash Point: > 200°F
Density (lb/gal): 9,83
Solid (% by weight): 46,00
Solid (% by volume): 34,20
Shelf Life (months): 12

Waterborne 1K

AQUASILK 200TW 1K WHITE 228-24XX

Find distributor Trouver un distributeur

spec_description:

AQUASILK 200TW 1K White Topcoat is an acrylic selfcrosslinking product that is utilized in various markets. It meets AWI system #7 and specific KCMA requirements.

AQUASILK 200TW 1K White Topcoat has unique thixotropy for vertical and horizontal application. It has excellent hiding properties.

Waterborne MaestroHue complete color sytem available utilizing 897 colorants at a maximum 7%.

BACKRetour

Product codeCodes de produit
Product Codes:

228-2405 FLAT,
228-2410 MATTE,
228-2420 LOW GLOSS,
228-2435 SATIN,
228-2450 SEMI-GLOSS,
228-2490 HIGH GLOSS

Product information

Product specificationsSpécifications du produit

Viscosity:
900 - 1100 cP at 77°F (25°C)
Flash Point: > 200°F
Density (lb/gal): 9,83
Solid (% by weight): 46,00
Solid (% by volume): 34,20
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_AQUASILK_200TW_1K_WHITE_228-24XX.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more