V-Primer

546-7257 V-Primer Pigmented Vinyl Primer

Product Codes:

546-7257

Surface Preparation:

Wood must be sanded with a 120 or 150 grit paper and free of dust and all contaminants. Before the application of the topcoat, the V-Primer must be sanded with a 280/320 grit paper. This primer must not be applied over metal, old oil finish or nitrocellulose lacquer.

General Information:

Agitate material before use. Keep under mixing to ensure product consistency. Apply one or two coats. A good sanding between coats with a #280/320 grit paper is necessary to obtain a good adhesion. This product could be catalyzed to enhance sanding properties but system must be evaluated and approved by AkzoNobel before going in production. For any information, contact your sales representative. If catalyzed, topcoat must be applied within 8 hours of sanding. Never apply more than 5 mils wet in one coat. Dry film thickness of V-Primer should not exceed 2 mils dry. Total dry film thickness of system should not exceed 5 mils dry.

To obtain complete cure, the primer must be applied at a temperature above 18ºC and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapors. Finished surface must not be cleaned with ammonia containing products.

Topcoats to use over 546-7257: 131-50XX, 131-51XX, 131-82XX, 117-30XX, 117-32XX, 421-67XX, 431-30XX, 484-6XXX, 421-72XX.

PDF Name: CA-PIS_546-7257_V-Primer_Pigmented_Vinyl_Primer

Tack Free Time: 45 - 60 minutes

Files: CA-PIS_546-7257_V-Primer_Pigmented_Vinyl_Primer.pdf

Dry to Sand : 60 - 90 minutes

Dry to Stack: 3 - 4 hours

Tack Free Time: Flash off before entering oven

Dry to Sand: 45 - 60 minutes

VOC less exempt g/l: 655

VOC g/l: 584

Dry to Stack: 1 - 2 hours

Note: N/A

Note:

See individual compliance sheets for specific data

spec_description:

V-Primer is a pigmented one-component vinyl primer. It provides superior moisture resistance along with adhesion over all wood species.

spec_uses:

V-Primer is recommended for kitchen cabinets, office or residential furniture as well as other interior wood applications.

Suggested Uses: Spray

Mixing Ratio:

N/A

Pot Life: N/A

Application Viscosity:

20 - 24 sec Zahn #2 at 25°C

Reducer: Lacquer thinner 803-1339/121-001 or 121-8020

Retarder: 800-5328 EEP

Clean-up Solvent: Lacquer Thinner

Recommended Wet Film: 3 - 5 mils wet

Coverage:

8 m²/l (90 pi²/l) at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

N/A

Viscosity:

Zahn #2 signature cup 22 sec at 25°C

Flash Point: -20°C

Density (lb/gal): 1.08 ± 2% at 25°C

Solid (% by weight): 38 ± 1%

Solid (% by volume): 20 ± 1%

Shelf Life (months): 12

V-Primer

546-7257 V-Primer Pigmented Vinyl Primer

Find distributor Trouver un distributeur

spec_description:

V-Primer is a pigmented one-component vinyl primer. It provides superior moisture resistance along with adhesion over all wood species.

BACK

V-Primer

546-7257 V-Primer Pigmented Vinyl Primer

spec_description:

V-Primer is a pigmented one-component vinyl primer. It provides superior moisture resistance along with adhesion over all wood species.

Product codeCodes de produit
Product Codes:

546-7257

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 22 sec at 25°C

Flash Point: -20°C

Density (lb/gal): 1.08 ± 2% at 25°C

Solid (% by weight): 38 ± 1%

Solid (% by volume): 20 ± 1%

Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_546-7257_V-Primer_Pigmented_Vinyl_Primer.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap