Chemlite

436-31XX Chemlite PU Clear Topcoat

Product Codes:

436-3108 10° Matte
436-3125 25° Low Gloss
436-3141 40° Satin
436-3191 90° High Gloss

Surface Preparation:

Topcoats should be well sanded using 240, 280 or 320 grit stearated paper.

General Information:

Mix the desired amount of material and apply 4-5 mils wet. Do not use excess reducer (>10%), this product is relatively low solids and will appear ‘hungry’ if too much thinner is added.
The relative humidity in the application and drying rooms should never exceed 75%. Viscosity on the catalyzed material should be monitored regularly to maintain a consistent appearance.
Mixed product will contain 999-067, an isocyanate based co reactant. Please follow all precautions associated with handling and use of these materials.
Total recommended film thickness of Chemlite is not to exceed 6 mils dry.

The sealer for this product is 436-2104.

PDF Name: CA-PIS_436-31XX_Chemlite_PU_Clear_Topcoat

Tack Free Time: 20 - 30 minutes

Files: CA-PIS_436-31XX_Chemlite_PU_Clear_Topcoat.pdf

Dry to Sand : Overnight

Dry to Stack: Overnight

Tack Free Time: Flash off before entering oven

Dry to Sand: 3 hours

VOC less exempt g/l: 715

VOC g/l: 715

Dry to Stack: 8 hours

Note: N/A

Note:

See individual compliance sheets for specific data

spec_description:

Chemlite is a two component polyurethane finish for interior use. The Chemlite system provides exceptional resistance to discolouration and gives a crosslinked finish that is tough and durable. The coating contains UV absorbers to minimize discolouration of light sensitive substrates.

spec_uses:

Chemlite is an excellent choice for finishing fine furniture, cabinetry and all other wood surfaces intended for interior use. Chemlite is also “water-white” meaning it is exceptional over pigmented basecoats where colour is important.

Suggested Uses: Spray

Mixing Ratio:

10 parts Chemlite, 2 parts 999-067 (20% b.v.)

Pot Life:

3 hours

Application Viscosity:

Zahn #2 signature cup 20-25 seconds

Reducer: 121-834 or 800-5301

Retarder: 800-5328 EEP

Clean-up Solvent: Lacquer Thinner (do not mix with product)

Recommended Wet Film: 4-5 wet mils

Coverage:

N/A

Note application:

N/A

Viscosity:

Zahn #2 signature cup 26 sec at 25°C

Flash Point: 24°C (75°F)

Density (lb/gal): 0.95

Solid (% by weight): 25%

Solid (% by volume): 19%

Shelf Life (months): 12

Chemlite

436-31XX Chemlite PU Clear Topcoat

Find distributor Trouver un distributeur

spec_description:

BACK

Chemlite

436-31XX Chemlite PU Clear Topcoat

spec_description:

Product codeCodes de produit
Product Codes:

436-3108 10° Matte
436-3125 25° Low Gloss
436-3141 40° Satin
436-3191 90° High Gloss

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 26 sec at 25°C

Flash Point: 24°C (75°F)

Density (lb/gal): 0.95

Solid (% by weight): 25%

Solid (% by volume): 19%

Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_436-31XX_Chemlite_PU_Clear_Topcoat.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap