- GLAZE
- 825-3680 Promatch® ProGlaze Neutral Wet Glaze
- Product Codes:
825-3680
- Surface Preparation:
N/A
- General Information:
Prior to use, agitate thoroughly and tint as required with 844 line tints to maximum of 25% by volume. The Promatch® ProGlaze Neutral Wet Glaze can be applied over washcoat, sealer, primer, enamel or topcoat. Must be re-coated with a clear topcoat afterwards. Sand with 280/320 grit paper before applying glaze. The glaze and topcoat must be applied within 8 hours of sanding.
Apply the Glaze by spraying or with a rag. Allow two to three minutes air drying before wiping. Wipe clean and do not leave on any excess material that may interfere with optimum adhesion.
Promatch® ProGlaze Neutral Wet Glaze must be thoroughly agitated to ensure product consistency.
Compatible with 436-48XX ora Verde® Chiaro, 431-46XX Varicure®, 131-53XX Varicure® Select, 421-63XX Chemlife®24, 117-27XX Chemlife®24 Plus, etc. - PDF Name: CA-PIS_825-3680_Promatch_ProGlaze_Neutral_Wet_Glaze
- Tack Free Time: N/A
- Files: CA-PIS_825-3680_Promatch_ProGlaze_Neutral_Wet_Glaze.pdf
- Dry to Sand : N/A
- Dry to Stack: N/A
- Tack Free Time: N/A
- test: N/A
- VOC less exempt g/l: 612
- VOC g/l: 612
- Dry to Stack: N/A
- Note:
N/A
- spec_description:
Promatch® ProGlaze Neutral Wet Glaze is an all-purpose wet glaze for furniture and cabinets. It is specially formulated to be used with 844 tints and can be tinted up to a mximum of 25% by volume. This universal solvent borne glaze provides good adhesion and workability with various technologies such as pre-cats, conversion varnishes and 2k polyurethane.
- spec_uses:
Promatch® ProGlaze Neutral Wet Glaze is used for coloring of wood on furniture, cabinets and millwork. When properly applied, it will enhance the natural beauty of the wood.
- Suggested Uses: Wood Glaze
- Mixing Ratio:
N/A
- Pot Life: N/A
- Application Viscosity:
N/A
- Reducer: N/A
- Retarder: N/A
- Clean-up Solvent: 121-001 / 803-1339
- Recommended Wet Film: N/A
- Coverage:
N/A
- Note application:
Applied spray or with rag, allow to dry, wipe or brush. Allow to dry.
- Viscosity:
N/A
- Flash Point: >93°C
- Density (lb/gal): 0.86
- Solid (% by weight): 29.2%
- Solid (% by volume): 21.8%
- Shelf Life (months): 24
- Spray Stain
- 890-3478 Solvent Borne Spray Stain Base
- Product Codes:
890-3478 Spray stain base
- Surface Preparation:
The substrate must be sanded with a #120, 150 or 180 grit sand paper and free of dust and all contaminants.
- General Information:
Product must be thoroughly agitated before use and during application for color consistency.
Apply a wet coat of the spray stain on the sanded surface. Let dry 20 to 30 minutes air dry before the application of the sealer. Keep under mixing to assure consistency of the product.
Maximum of colorants to be used in this base is 15% by volume. A maximum of 4% of dyes could also be used.
- PDF Name: CA-PIS_890-3478_Solvent_Borne_Spray_Stain_Base
- Tack Free Time: 20 - 30 minutes
- Files: CA-PIS_890-3478_Solvent_Borne_Spray_Stain_Base.pdf
- Dry to Sand : N/A
- Dry to Stack: N/A
- Tack Free Time: N/A
- test: N/A
- VOC less exempt g/l: 797
- VOC g/l: 640
- Dry to Stack: N/A
- Note:
See individual compliance sheets for specific data
- spec_description:
Spray stain base formulated especially to be tinted with 866 colorants. Its unique solvent blend also gives the option of using dyes for the development of rich and deep colors.
- spec_uses:
890-3478 is a spray stain base that gives you the opportunity to develop a variety of colors for interior wood application.
- Suggested Uses: Spray
- Mixing Ratio:
N/A
- Pot Life: N/A
- Application Viscosity:
N/A
- Reducer: N/A
- Retarder: N/A
- Clean-up Solvent: Lacquer Thinner
- Recommended Wet Film: 2 - 4 mils wet
- Coverage:
N/A
- Note application:
N/A
- Viscosity:
N/A
- Flash Point: -20°C
- Density (lb/gal): 0.83 ± 2% at 25°C
- Solid (% by weight): 3 - 4%
- Solid (% by volume): 2 - 3%
- Shelf Life (months): 24
- Promatch®
- 890-4041 Promatch® Solvent Borne Spray Stain Base
- Product Codes:
890-4041 Spray stain base
- Surface Preparation:
The substrate must be sanded with a #120, 150 or 180 grit sand paper and free of dust and all contaminants.
- General Information:
Product must be thoroughly agitated before use and during application for color consistency.
Apply a wet coat of the spray stain on the sanded surface. Let dry a minimum of 10 minutes air dry before the application of the sealer. Keep under mixing to assure consistency of the product.
Can be tinted with 844 tints and/or with dyes at a maximum of 15% volume.
- PDF Name: CA-PIS_890-4041_Promatch_Solvent_Borne_Spray_Stain_Base
- Tack Free Time: 10 minutes
- Files: CA-PIS_890-4041_Promatch_Solvent_Borne_Spray_Stain_Base.pdf
- Dry to Sand : N/A
- Dry to Stack: N/A
- Tack Free Time: N/A
- test: N/A
- VOC less exempt g/l: 858
- VOC g/l: 858
- Dry to Stack: N/A
- Note:
See individual compliance sheets for specific data
- spec_description:
Ready to use spray stain that gives little or no grain raising. Formulated especially to be tinted with 844 colorants. Its unique solvent blend also gives the option of using dyes for the development of rich and deep colors.
- spec_uses:
890-4041 is a spray stain base that gives you the opportunity to develop a variety of colors for interior wood application.
- Suggested Uses: Spray
- Mixing Ratio:
N/A
- Pot Life: N/A
- Application Viscosity:
N/A
- Reducer: N/A
- Retarder: N/A
- Clean-up Solvent: Lacquer Thinner
- Recommended Wet Film: 2 - 4 mils wet
- Coverage:
N/A
- Note application:
N/A
- Viscosity:
N/A
- Flash Point: -3°C (26°F)
- Density (lb/gal): 0.86 ± 2% at 25°C
- Solid (% by weight): 0%
- Solid (% by volume): 0%
- Shelf Life (months): 24
- Promatch®
- 890-4120 Promatch® Solvent Borne Spray Stain Base
- Product Codes:
890-4120 Spray stain base
- Surface Preparation:
The substrate must be sanded with a #120, 150 or 180 grit sand paper and free of dust and all contaminants.
- General Information:
Product must be thoroughly agitated before use and during application for color consistency.
Apply a wet coat of the spray stain on the sanded surface. Let dry 20 - 30 minutes air dry before the application of the sealer. Keep under mixing to assure consistency of the product.
To be tinted with 844 tints only at a maximum of 15% volume.The of dyes is not possible in this base.
- PDF Name: CA-PIS_890-4120_Promatch_Solvent_Borne_Spray_Stain_Base
- Tack Free Time: 20 - 30 minutes
- Files: CA-PIS_890-4120_Promatch_Solvent_Borne_Spray_Stain_Base.pdf
- Dry to Sand : N/A
- Dry to Stack: N/A
- Tack Free Time: N/A
- test: N/A
- VOC less exempt g/l: 857
- VOC g/l: 857
- Dry to Stack: N/A
- Note:
See individual compliance sheets for specific data.
- spec_description:
890-4120 spray stain base formulated especially to be tinted with 844 colorants.
- spec_uses:
890-4120 is a spray stain base that gives you the opportunity to develop a variety of colors for interior wood application.
- Suggested Uses: Spray
- Mixing Ratio:
N/A
- Pot Life: N/A
- Application Viscosity:
N/A
- Reducer: N/A
- Retarder: N/A
- Clean-up Solvent: Lacquer Thinner
- Recommended Wet Film: 2 - 4 mils wet
- Coverage:
N/A
- Note application:
N/A
- Viscosity:
N/A
- Flash Point: 4°C
- Density (lb/gal): 0.86 ± 2% at 25°C
- Solid (% by weight): 0%
- Solid (% by volume): 0%
- Shelf Life (months): 24
- Promatch®
- 825-34XX Promatch® Dry Glaze
- Product Codes:
825-3410 Neutral Base
825-3411 White Base
825-3414 Yellow tint
825-3415 Brown tint
825-3416 Black tint
825-3417 Red tint
- Surface Preparation:
The substrate must be sanded with a #120, 150 or 180 grit sand paper and free of dust and all contaminants.
- General Information:
Apply Dry Glaze at approximately 3-4 mils wet over sealer coat. Allow to flash off and remove excess material with a solvent‑wetted rag or "Scotch‑Brite" pad. To ensure good adhesion of the finished system, as much filler as possible should be removed from the exposed areas.
825-3410 and 825-3411 are designed to be tinted with Dry Glaze Tints from the 825-34XX line, the use of liquid tinters will complicate the removal process and is not recommended.
- PDF Name: CA-PIS_825-34XX_Promatch_Dry_Glaze
- Tack Free Time: 15 - 20 minutes
- Files: CA-PIS_825-34XX_Promatch_Dry_Glaze.pdf
- Dry to Sand : 15 - 20 minutes
- Dry to Stack: N/A
- Tack Free Time: N/A
- test: 10 -15 minutes
- VOC less exempt g/l: 766 Neutral 755 White, 684-696 Tints
- VOC g/l: 766 Neutral 755 White, 684-696 Tints
- Dry to Stack: N/A
- Note:
See individual compliance sheets for specific data.
- spec_description:
Concentrated pigment dispersion designed to provide an antiquated effect to furniture, cabinets and paneling.
- spec_uses:
Use as protective coatings on all type of wood.
For interior use only.
- Suggested Uses: Spray
- Mixing Ratio:
N/A
- Pot Life: N/A
- Application Viscosity:
As is
- Reducer: N/A
- Retarder: N/A
- Clean-up Solvent: Lacquer Thinner
- Recommended Wet Film: 2-4 mils wet
- Coverage:
N/A
- Note application:
N/A
- Viscosity:
Zahn #2 signature cup 13 sec at 25°C (Neutral)
Zahn #2 signature cup 18 sec at 25°C (White)
- Flash Point: 12°C Neutral/White base, 7°C Tints
- Density (lb/gal): @25°C 0.92 White, 0.86 Neutral/Tints
- Solid (% by weight): 10% Neutral, 18% White, 20% Tints
- Solid (% by volume): 4% Neutral, 6% White, 12-13% Tints
- Shelf Life (months): 24
Need help? Contact our team of wood coating experts.
