Promatch®

151-3130 Promatch® Wipe Stain Base

Product Codes:

151-3130 Wipe Stain Base

(151-313)

Surface Preparation:

The substrate must be sanded with a 120, 150 or 180 grit sand paper and free of dust and all contaminants.

General Information:

Product must be thoroughly agitated before use and during application for color consistency.

Apply a wet coat of the wipe stain. Wipe off the stain using a clean rag. Let dry 30 to 60 minutes air dry before the application of the sealer.

Can be tinted with 886 tints at a maximum of 30% by volume and/or with dyes at a maximum of 5% by volume.

To obtain complete cure, system should be applied at a temperature above 18°C and relative humidity below 65%.

PDF Name: CA-PIS_151-3130_Promatch_Wipe_Stain_Base

Tack Free Time: N/A

Files: CA-PIS_151-3130_Promatch_Wipe_Stain_Base.pdf

Dry to Sand : N/A

Dry to Stack: N/A

Tack Free Time: N/A

test: N/A

VOC less exempt g/l: 842

VOC g/l: 754

Dry to Stack: N/A

Note: N/A

Note:

See individual compliance sheets for specific data

spec_description:

151-3130 is a wipe stain formulated especially to be tinted with 866 tints. Its unique solvent blend also gives the option of using dyes for the development of rich and deep color.

spec_uses:

151-3130 offers a simple one step stain system with very good clarity and grain fill. Its ease of workability and good open time allow for uniform appearance on large pieces.

Suggested Uses: Spray / Wipe

Mixing Ratio:

N/A

Pot Life: N/A

Application Viscosity:

N/A

Reducer: N/A

Retarder: N/A

Clean-up Solvent: Lacquer Thinner

Recommended Wet Film: 3 - 5 mils wet

Coverage:

N/A

Note application:

N/A

Viscosity:

Zahn #2 signature cup 22 sec at 25°C

Flash Point: -20°C

Density (lb/gal): 0.93 ± 2% at 25°C

Solid (% by weight): 8-9%

Solid (% by volume): 6-7%

Shelf Life (months): 24

Promatch®

151-3130 Promatch® Wipe Stain Base

Find distributor Trouver un distributeur

spec_description:

151-3130 is a wipe stain formulated especially to be tinted with 866 tints. Its unique solvent blend also gives the option of using dyes for the development of rich and deep color.

BACK

Promatch®

151-3130 Promatch® Wipe Stain Base

spec_description:

151-3130 is a wipe stain formulated especially to be tinted with 866 tints. Its unique solvent blend also gives the option of using dyes for the development of rich and deep color.

Product codeCodes de produit
Product Codes:

151-3130 Wipe Stain Base

(151-313)

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 22 sec at 25°C

Flash Point: -20°C

Density (lb/gal): 0.93 ± 2% at 25°C

Solid (% by weight): 8-9%

Solid (% by volume): 6-7%

Shelf Life (months): 24

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_151-3130_Promatch_Wipe_Stain_Base.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap