New Selva Pro- Isolante Sealer
- 420-1205 Isolante Sealer
- Product Codes:
420-1205
- Surface Preparation:
Wood must be sanded with a #120 or 150 grit paper and free of dust and all contaminants.
- General Information:
Apply 3 to 5 wet mils on a sanded surface. Let dry for 30 to 60 minutes and apply the desired topcoat. If the drying time exceeds 4 hours, sanding is required to keep a good adhesion. Once catalyzed with 876-9084, this product will contain isocyanates. Take necessary precautions for the handling and use of this product. See MSDS. AkzoNobel recommends using Promatch® W/S 151-3130, Promatch® Easywipe 825-7200, Promatch C-Mix Wipe Stains 825-90XX. Spray Stain 890-3478, Promatch® S/S Base 890-4041 and 890-4120.
For a complete system cure, the system must be applied at a temperature above 18ºC and relative humidity below 65%Complete system must be verified and approved by AkzoNobel before going on production.
- PDF Name: CA-PIS_420-1205_Isolante_Sealer
- Tack Free Time: 30-60 minutes
- Files: CA-PIS_420-1205_Isolante_Sealer.pdf
- Dry to Sand : 4 hours
- Dry to Stack: N/A
- Tack Free Time: 15-20 minutes
- Dry to Sand: 30 minutes
- VOC less exempt g/l: 698
- VOC g/l: 698
- Dry to Stack: N/A
- Note:
N/A
- spec_description:
Selva Pro Isolante 2K Sealer is designed to enhance adhesion on exotic or oily substrates. Its features include strong bond, barrior coat properties and ease of sandability, making it ideal for high-end wood applications.
- spec_uses:
Used as a barrior coat on exotic substrates and or as an adhesion promoter under any Selva Pro sealers or Chemcraft's polyester sealer.
- Suggested Uses: Wood Finishes
- Mixing Ratio:
100 Parts 420-1205 with 50 Parts 876-9084 (by volume)
- Pot Life: 4 hours
- Application Viscosity:
20-22 sec Zahn #2 at 77° F (25°C)
- Reducer: 803-2000
- Retarder: N/A
- Clean-up Solvent: 800-5500 Acetone
- Recommended Wet Film: 3-5 wet mils
- Coverage:
N/A
- Note application:
N/A
- Viscosity:
27-29 sec Zahn #2 at 77° F (25°C)
- Flash Point: 21.2° F (9° C)
- Density (lb/gal): 0.84
- Solid (% by weight): 22.8
- Solid (% by volume): 15.2
- Shelf Life (months): 24
- Selva Pro
- 109-17XX Selva™ Pro Bianco Polyurethane Pigmented Topcoat
- Product Codes:
109-1705 Flat
109-1715 Matte
109-1725 Low Gloss
109-1735 Satin
109-1750 Semi-Gloss
109-1780 High Gloss - Surface Preparation:
Substrate must be sanded using 120, 150 or 180 grit paper prior to priming. Primer should be sanded with 320 grit paper prior to being coated, The Primer should be coated within eight hours of being sanded. Appropriate primers are the Selva Pro 536-1700, 536-1701, or 536-1702 as well it is compatible with waterborne primer options 550-1600, 550-2210, 550-1760 and 550-3400. When recoating, the previous coat of Bianco must be sanded and the next coat applied within eight hours.
- General Information:
The mixed product contains 876-9700, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of those materials. Refer to MSDS for detail information. Oil stains must be avoided because they will interfere with the adhesion.
Product must be thoroughly stirred before adding the hardener in the recommended ratio. The viscosity of the product should be monitored after mixing with the hardener. The relative humidity in the application and drying room should not exceed 75% for maximum coating performance.
- PDF Name: CA-PIS_109-17XX_Selva_Pro_Bianco_Polyurethane_Pigmented_Topcoat
- Tack Free Time: 15 minutes
- Files: CA-PIS_109-17XX_Selva_Pro_Bianco_Polyurethane_Pigmented_Topcoat.pdf
- Dry to Sand : 2 hours
- Dry to Stack: 24 hours
- Tack Free Time: 10 minutes
- Dry to Sand: 30 minutes
- VOC less exempt g/l: 482
- VOC g/l: 482
- Dry to Stack: 1 hour
- Note:
N/A
- spec_description:
This white PU topcoat builds quickly to deliver a smooth, high-end finish. Fast drying and easy to apply, it offers excellent hiding power, lasting durability and flexibility. It can be used as a white system or tinted with 844's (max 10% by vol) for a versatile color range to meet diverse design needs. With a soft, silky touch, it achieves an outstanding luxurious feel.
- spec_uses:
Ideal for high-end kitchen and bathroom cabinetry, as well as a wide range of interior wood applications, including architectural millworks, store fixtures, and office furniture.
- Suggested Uses: Wood Finishes
- Mixing Ratio:
100 Parts 109-17XX with 50 Parts 876-9700 (by volume)
- Pot Life: 3-4 hours depending on temperature and humidity
- Application Viscosity:
Zahn #2 signature cup 22-25 seconds at 25° C
- Reducer: 803-2000
- Retarder: 800-2001 3-5% by volume
- Clean-up Solvent: 800-5500 Acetone
- Recommended Wet Film: 4-6 wet mils
- Coverage:
N/A
- Note application:
MAXIMUM DRY FILM THICKNESS OF THE SYSTEM MUST NOT EXCEED 8 DRY MILS
- Viscosity:
Zahn #3 signature cup 38-42 sec at 25° C
- Flash Point: 7° C
- Density (lb/gal): 1.32
- Solid (% by weight): 64.5
- Solid (% by volume): 45.3
- Shelf Life (months): 24
- Selva Pro
- 109-4995 Selva™ Pro Lucido Polyurethane High Gloss White Topcoat
- Product Codes:
109-4995
- Surface Preparation:
Wood substrate should be sanded with 120 and 150 grit prior to application to ensure good adhesion. Sealers and primers should be well sanded using 240, 280 and 320 grit stearated paper. Suitable primers are polyurethane (536-1700, 536-1701 or 536-1702) or polyester (458-XXXX). For optimal performance primers should be coated within 8 hours of sanding. Care should be taken during sanding to avoid sanding through the primer.
- General Information:
Mix the desired amount of material and apply 3-5 mils wet. The coating when cured is very suitable to be buffed and polished where dust free conditions are not available. Allow product to cure (>24 hours) prior to buffing to reduce shrink-back. The relative humidity in the application and drying rooms should never exceed 75%. Viscosity on the mixed material should be monitored regularly to maintain a consistent appearance.
The mixed product contains 876-9701, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of these materials.
- PDF Name: CA-PIS_109-4995_Selva_Pro_Lucido_Polyurethane_High_Gloss_White_Topcoat
- Tack Free Time: 30-45 minutes
- Files: CA-PIS_109-4995_Selva_Pro_Lucido_Polyurethane_High_Gloss_White_Topcoat.pdf
- Dry to Sand : 8-12 hours
- Dry to Stack: 3 hours
- Tack Free Time: 20-30 minutes
- Dry to Sand: 4-6 hours
- VOC less exempt g/l: 412
- VOC g/l: 412
- Dry to Stack: 2 hours
- Note:
N/A
- spec_description:
Selva Pro Lucido White High Gloss is a high-performance, wet-look, two-component polyurethane coating. It can be cut and polished easily making it ideal for high-end woodwork offering high build with high gloss retention and clarity. It can tinted with
844's tints for a variety of pastel shades. - spec_uses:
Great choice where a very high gloss finish is required. Uses include interior cabinetry, interior marine and aircraft cabinetry, store fixtures, and musical instruments.
- Suggested Uses: Wood Finishes
- Mixing Ratio:
1:1 with 876-9701
- Pot Life: 3-4 hours depending on temperature and humidity
- Application Viscosity:
Zahn #2 signature cup 20-25 seconds
- Reducer: 803-2000
- Retarder: 800-2001 3-5% by volume
- Clean-up Solvent: 800-5500 Acetone
- Recommended Wet Film: 4-6 wet mils
- Coverage:
N/A
- Note application:
MAXIMUM DRY FILM THICKNESS OF THE SYSTEM MUST NOT EXCEED 8 DRY MILS
- Viscosity:
Zahn #3 signature cup 30-35 sec at 25° F
- Flash Point: 27° C
- Density (lb/gal): 1.32
- Solid (% by weight): 69.7
- Solid (% by volume): 55.9
- Shelf Life (months): 24
- Selva Pro
- 109-19XX Selva™ Pro Neutral Polyurethane Pigmented Topcoat
- Product Codes:
109-1905 Flat
109-1915 Matte
109-1925 Low Gloss
109-1935 Satin
109-1950 Semi-Gloss
109-1980 High Gloss - Surface Preparation:
Substrate must be sanded using 120, 150 or 180 grit paper prior to priming. Primer should be sanded with 320 grit paper prior to being coated, The Primer should be coated within eight hours of being sanded. Appropriate primers are the Selva Pro 536-1700, 536-1701, or 536-1702 as well as compatible waterborne primers options; 550-1600, 550-2210, 550-1760, and
550-3400. When recoating, the previous coat of Bianco must be sanded and the next coat applied within eight hours. - General Information:
The mixed product contains 876-9700, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of those materials. Refer to MSDS for detail information. Oil stains must be avoided because they will interfere with the adhesion.
Product must be thoroughly stirred before adding the hardener in the recommended ratio. The viscosity of the product should be monitored after mixing with the hardener. The relative humidity in the application and drying room should not exceed 75% for maximum coating performance.
- PDF Name: CA-PIS_109-19XX_Selva_Pro_Neutral_Polyurethane_Pigmented_Topcoat
- Tack Free Time: 15 minutes
- Files: CA-PIS_109-19XX_Selva_Pro_Neutral_Polyurethane_Pigmented_Topcoat.pdf
- Dry to Sand : 3 hours
- Dry to Stack: 24 hours
- Tack Free Time: 10 minutes
- Dry to Sand: 30 minutes
- VOC less exempt g/l: 522
- VOC g/l: 522
- Dry to Stack: 1 hour
- Note:
N/A
- spec_description:
This premium PU neutral topcoat delivers a smooth, high-end finish with minimal effort. Tintable with 844's (max 10% by vol.) it offers fast drying, easy application, excellent hiding, durability and flexibility. Its soft, silky touch provides a luxurious, tactile feel. This premium, neutral PU topcoat quickly builds to deliver a smooth, high-end finish with minimal effort.
- spec_uses:
Ideal for high-end kitchen and bathroom cabinetry, as well as a wide range of interior wood applications, including architectural millworks, store fixtures and office furniture.
- Suggested Uses: Wood Finishes
- Mixing Ratio:
100 Parts 109-19XX with 50 Parts 876-9700 (by volume)
- Pot Life: 3-4 hours depending on temperature and humidity
- Application Viscosity:
Zahn #3 signature cup 22-25 sec at 25° C
- Reducer: 803-2000
- Retarder: 800-2001 3-5% by volume
- Clean-up Solvent: 800-5500 Acetone
- Recommended Wet Film: 4-6 wet mils
- Coverage:
N/A
- Note application:
MAXIMUM DRY FILM THICKNESS OF THE SYSTEM MUST NOT EXCEED 8 DRY MILS
- Viscosity:
Zahn #3 signature cup 27-30 sec at 25° C
- Flash Point: 7° C
- Density (lb/gal): 0.96
- Solid (% by weight): 50.0
- Solid (% by volume): 41.0
- Shelf Life (months): 24
- Selva Pro
- 436-57XX Selva™ Pro Chiaro Polyurethane Clear Topcoat
- Product Codes:
436-5705 Flat
436-5715 Matte
436-5725 Low Gloss
436-5735 Satin
436-5750 Semi-Gloss
436-5780 High Gloss - Surface Preparation:
Substrate must be sanded using 120, 150 or 180 grit paper prior to staining or coating. Sealer should be sanded with 280/320 grit paper prior to being coated. The sealer should be coated within eight hours of being sanded. Appropriate sealer is the Selva Pro Chiaro Sealer 436-5700. When recoating, the previous coat of Chiaro must be sanded and the next coat applied within eight hours. Stain systems used under Chiaro are formulated to develop excellent grain definition.
AkzoNobel recommends using Promatch® W/S 151-3130, Promatch® Easywipe 825-7200, Promatch C-Mix Wipe Stains
825 90XX. Spray Stain 890-3478, Promatch® S/S Base 890-4041 and 890-4120. - General Information:
The mixed product contains 876-9700, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of those materials. Refer to MSDS for detail information. Oil stains must be avoided because they will interfere with the adhesion. When coating exotic woods (Teak, Rosewood, etc.) a barrier coat (tie-coat) should be applied before the sealer or base coat. See Product data sheet for 420-1205 Isolante.
Product must be thoroughly stirred before adding the hardener in the recommended ratio. The viscosity of the product should be monitored after mixing with the hardener. The relative humidity in the application and drying room should not exceed 75% for maximum coating performance.
- PDF Name: CA-PIS_436-57XX_Selva_Pro_Chiaro_Polyurethane_Clear_Topcoat
- Tack Free Time: 15 minutes
- Files: CA-PIS_436-57XX_Selva_Pro_Chiaro_Polyurethane_Clear_Topcoat.pdf
- Dry to Sand : 2 hours
- Dry to Stack: 24 hours
- Tack Free Time: 10 minutes
- Dry to Sand: 30 minutes
- VOC less exempt g/l: 545
- VOC g/l: 545
- Dry to Stack: 1 hour
- Note:
N/A
- spec_description:
Selva Pro Chiaro Clear Topcoat is an ultra-clear polyurethane, specially formulated for versatility and exceptional durability. With outstanding physical properties, chemical resistance, and superior impact resistance, Chiaro provides a luxurious finish and a smooth feel. Its ease of application and rapid drying time make it an ideal choice for high-end woodwork.
- spec_uses:
An excellent choice for surfaces demanding enhanced chemical resistance, Selva Pro Chiaro is ideal for applications such as interior cabinetry, marine interiors, store fixtures, and musical instruments.
- Suggested Uses: Wood Finishes
- Mixing Ratio:
100 Parts 436-57XX with 50 Parts 876-9700 (by volume)
- Pot Life: 3-4 hours depending on temperature and humidity
- Application Viscosity:
Zahn #2 signature cup 22-25 seconds.
- Reducer: 803-2000
- Retarder: 800-2001 3-5% by volume
- Clean-up Solvent: 800-5500 Acetone
- Recommended Wet Film: 4-6 wet mils
- Coverage:
N/A
- Note application:
MAXIMUM DRY FILM THICKNESS OF THE SYSTEM MUST NOT EXCEED 6 DRY MILS
- Viscosity:
Zahn #3 signature cup 25-28 sec at 25° C
- Flash Point: 7° C
- Density (lb/gal): 0.96
- Solid (% by weight): 45.45
- Solid (% by volume): 37.25
- Shelf Life (months): 24
Need help? Contact our team of wood coating experts.
