Sadowhite
117-30XX Sadowhite Post-Cat Pigmented Topcoat
Product Codes:

117-3010 10° Matte
117-3020 20° Low Gloss
117-3035 35° Satin
117-3050 50° Semi-Gloss
117-3090 90° High Gloss

Surface Preparation:

Primer must be sanded with a #280/320 paper before application of the topcoat and must be recovered within 8 hours after sanding. Care should be taken during sanding to avoid sanding through the primer. Sadowhite must not be applied over metal, old finish or nitrocellulose lacquer.

General Information:

Catalyze and reduce material as recommended. To ensure proper sheen, the catalyzed material should be agitated at all times. Contact with metal surfaces should be avoided once the Sadowhite has been catalyzed. Apply 3-5 mils wet on sanded surface. A subsequent coat can be applied after complete cure and a good sanding with a #280/320 grit paper is necessary to obtain a good adhesion. Dry film thickness of topcoat must not exceed 3 mils. Total dry film thickness of system should not exceed 6 mils.

To obtain complete cure, the primer must be applied at a temperature above 18ºC and relative humidity below 65%. When drying, this product is not to be exposed to ammonia vapors. Finished surface must not be cleaned with ammonia containing products.

Primers to use with 117-30XX: 220-005, 220-2250, 225-0010, 522-1624, 545-8016 and 546-7257.

PDF Name: CA-PIS_117-30XX_Sadowhite_Post-Cat_Pigmented_Topcoat
Tack Free Time: 30 - 45 minutes
Files: CA-PIS_117-30XX_Sadowhite_Post-Cat_Pigmented_Topcoat.pdf
Dry to Sand : 90 - 120 minutes
Dry to Stack: 12 hours
Tack Free Time: Flash off before entering oven
Dry to Sand: 45 - 60 minutes
VOC less exempt g/l: 435
VOC g/l: 435
Dry to Stack: 2 hours
Note: N/A
Note:

See individual compliance sheets for specific data

spec_description:

Sadowhite is an acid curing, light stable, high-solids FAST DRYING Reactive Amino Coating (RAC) with good building properties. This is a fast building product due to its high solid content (49% volume). It gives a smooth, knock-proof and hard-wearing surface resisting influence from alcohol, water, etc. Sadowhite has very good light stability based on the type of resin used.

spec_uses:

Used as the final coat over wood, plywood, chipboard, etc. meant for interior use. This product is recommended for kitchen cabinets, high build office or residential furniture as well as many other interior wood applications where high build and durability are required.

Suggested Uses:

Spray

Mixing Ratio:

10% 999-031A

Pot Life: 4 hours
Application Viscosity:

22-30 sec Zahn #2 at 25°C

Reducer: 10-20% with 121-8020
Retarder: 800-5328 EEP
Clean-up Solvent: Lacquer Thinner
Recommended Wet Film: 3 to 5 mils wet
Coverage:

19 m2/l (205 pi2/l) at 1 mil dry and at 100% efficiency. Coverage will vary depending on method of application or coating thickness.

Note application:

N/A

Viscosity:

Zahn #3 signature cup 21 sec at 25°C

Flash Point: 20°C
Density (lb/gal): 1.13 ± 2% at 25°C
Solid (% by weight): 62 ± 1%
Solid (% by volume): 49 ± 1%
Shelf Life (months): 12

Sadowhite

117-30XX Sadowhite Post-Cat Pigmented Topcoat

Find distributor Trouver un distributeur

spec_description:

Sadowhite is an acid curing, light stable, high-solids FAST DRYING Reactive Amino Coating (RAC) with good building properties. This is a fast building product due to its high solid content (49% volume). It gives a smooth, knock-proof and hard-wearing surface resisting influence from alcohol, water, etc. Sadowhite has very good light stability based on the type of resin used.

Read more

Sadowhite

117-30XX Sadowhite Post-Cat Pigmented Topcoat

spec_description:

Sadowhite is an acid curing, light stable, high-solids FAST DRYING Reactive Amino Coating (RAC) with good building properties. This is a fast building product due to its high solid content (49% volume). It gives a smooth, knock-proof and hard-wearing surface resisting influence from alcohol, water, etc. Sadowhite has very good light stability based on the type of resin used.

Read more
Product codeCodes de produit
Product Codes:

117-3010 10° Matte
117-3020 20° Low Gloss
117-3035 35° Satin
117-3050 50° Semi-Gloss
117-3090 90° High Gloss


Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #3 signature cup 21 sec at 25°C

Flash Point: 20°C
Density (lb/gal): 1.13 ± 2% at 25°C
Solid (% by weight): 62 ± 1%
Solid (% by volume): 49 ± 1%
Shelf Life (months): 12

Download product information sheets

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Image

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Need help? Contact our team of wood coating experts.

Contact us