Acquaduro
550-1601 Acquaduro™ 1K Waterborne Neutral Primer
Product Codes:

550-1601

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit paper prior to coating. 

Acquaduro™ 1K Waterborne
Neutral Primer should be sanded with 280/320 grit paper prior to being coated. 

Acquaduro™ 1K Waterborne Neutral Primer should be coated within (8) hours of being sanded for maximum adhesion.

General Information:

Mix material before use. Add water to reduce if required and mix thoroughly. Apply by spray at 4 - 6 mils wet. Acquaduro™ 1K
Waterborne Neutral Primer must be agitated thoroughly at all times to ensure product consistency. Contact with metal surfaces
should be avoided. Maximum film build of total coating system must not exceed 4 mils dry.
THE CUSTOMER IS RESPONSIBLE FOR FOLLOWING THE RECOMMENDED APPLICATION PROCEDURES. FAILURE TO ADHERE TO THE
RECOMMENDATIONS GIVEN IN THIS DATA SHEET WILL LIKELY RESULT IN UNSATISFACTORY FILM APPEARANCE OR FILM FAILURE. THE
COMPLETE COATING SYSTEM SHOULD BE CHECKED FOR REQUIRED PROPERTIES PRIOR TO THE START-UP OF PRODUCTION.

PDF Name: CA-PIS_550-1601_Acquaduro_1K_Waterborne_Neutral_Primer
Tack Free Time: 10 minutes
Files: CA-PIS_550-1601_Acquaduro_1K_Waterborne_Neutral_Primer.pdf
Dry to Sand : 20 minutes
Dry to Stack: 12 hours
Tack Free Time: 5 minutes
Dry to Sand: 10 minutes
VOC less exempt g/l: 48.0
VOC g/l: 19.0
Dry to Stack: 30 minutes
Note: N/A
Note:

N/A

spec_description:

Acquaduro™ 1K Neutral Primer is a ready to use neutral waterborne primer. This waterborne primer provides excellent durability and water resistance on hardwoods or MDF. Acquaduro Waterborne Primer has great ease of application and fast application and dry times.
Recommended topcoat is the Acquaduro 2K Pigmented or Neutral  Polyurethane Waterborne Topcoat.

spec_uses:

Acquaduro™ 1K Waterborne Neutral Primer has been designed for the cabinet, architectural millwork, furniture and refinish
markets.

Suggested Uses: Designed for use on hardwoods or MDF
Mixing Ratio:

N/A

Pot Life: N/A
Application Viscosity:

Zahn #2 Signature cup 30-35 sec at 25º C

Reducer: Use water if required
Retarder: 970-1358 1 to 3 % by Volume
Clean-up Solvent: Water
Recommended Wet Film: 4-6 wet mils
Coverage:

610 sqft/gal

Note application:

N/A

Viscosity:

Zahn #2 Signature Cup 30-35 seconds at 25ºC

Flash Point: >93.3°C (200°F)
Density (lb/gal): 11.31
Solid (% by weight): 56.4
Solid (% by volume): 40.7
Shelf Life (months): 12
Acquaduro
228-36XX Acquaduro™ Neutral 2K Polyurethane Waterborne Topcoat
Product Codes:

228-3610 Matte
228-3620 Low Gloss
228-3635 Satin
228-3650 Semi-Gloss
228-3680 Gloss

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit paper prior to priming. Primer should be sanded with 280/320 grit paper prior to being coated, The Primer should be coated within eight hours of being sanded. Appropriate primers are the Chemcraft Acquaduro™ Primer 550-1760 or 550-1761. When recoating, the previous coat of the Acquaduro™ 2K Polyurethane Waterborne Topcoat must be sanded and the next coat applied within eight hours of being sanded.

General Information:

**After mixing part A and part B to the correct ratio, water can then be added to reduce viscosity prior to application as needed depending on spray equipment. A maximum of 10% water can be added to the fresh (immediately after the part B is fully dispersed into part A) catalyzed material.

Note: Adding extra water during application is not recommended as this will have a direct impact on the pot life. The pot life of the mixture will be reduced significantly, and the mixture will gel quickly. The mixed product contains 876-3400, an isocyanate-based co-reactant. Please follow all precautions associated with handling and use of those materials. Refer to MSDS for detailed information. Product must be thoroughly stirred before adding the hardener in the recommended ratio. The viscosity of the product should be monitored after mixing with the hardener. The relative humidity in the application and drying room should not exceed 75% for maximum coating performance.

THE CUSTOMER IS RESPONSIBLE FOR FOLLOWING THE RECOMMENDED APPLICATION PROCEDURES. FAILURE TO ADHERE TO THE
RECOMMENDATIONS GIVEN IN THIS DATA SHEET WILL LIKELY RESULT IN UNSATISFACTORY FILM APPEARANCE OR FILM FAILURE. THE
COMPLETE COATING SYSTEM SHOULD BE CHECKED FOR REQUIRED PROPERTIES PRIOR TO THE START-UP OF PRODUCTION.

PDF Name: CA-PIS_228-36XX_Acquaduro_Neutral_2K_Polyurethane_Waterborne_Topcoat
Tack Free Time: 20 minutes
Files: CA-PIS_228-36XX_Acquaduro_Neutral_2K_Polyurethane_Waterborne_Topcoat.pdf
Dry to Sand : 45 minutes
Dry to Stack: 24 hours
Tack Free Time: 12 minutes
Dry to Sand: 20 minutes
VOC less exempt g/l: 80.3
VOC g/l: 26.4
Dry to Stack: 30 minutes
Note: N/A
Note:

N/A

spec_description:

Acquaduro™ is a neutral 2K polyurethane waterborne topcoat for industrial application. This product is a neutral base to be tint to any desired color. This product provides excellent water and chemical resistance. Whether you are at the finishing shop or at a professional on-site job this low VOC and low odor system meets or exceeds industry standards.

spec_uses:

Acquaduro™ Neutral 2K Polyurethane Waterborne Topcoat has been designed for cabinet, architectural millwork, furniture and refinish markets.

Suggested Uses: For cabinet, architectural millwork, furniture, refinish markets
Mixing Ratio:

8% by volume of 876-3400 hardener

Pot Life: 3-4 hours depending on external condition
Application Viscosity:

Zahn #3 Signature cup 30-35 sec at 77°F (25°C)

Reducer: Water up to 10% by volume
Retarder: 870-1358 1 to 3 % by volume
Clean-up Solvent: Water
Recommended Wet Film: 4-5 wet mils
Coverage:

560 sqft/gal

Note application:

Polyurethane base should be thoroughly mixed first then hardener must be slowly added during agitation, product must be mixed for 1-2 minutes.

Customer must wait 5 minutes for "induction time" before usage. Mix only what you can use for 2-3 hours at a time.

If an excessive amount over 5 wet mils is applied, there is a chance that surface imperfection (mud cracking, etc.) may result.

Viscosity:

Zahn #2 Signature cup 40-45 sec at 77°F (25°C)
Zahn #3 Signature cup 18-22 sec at 77°F (25°C)

Flash Point: >200°F
Density (lb/gal): 8.78
Solid (% by weight): 33.5
Solid (% by volume): 29.5
Shelf Life (months): 12
Acquaduro
228-34XX Acquaduro™ Pigmented 2K Polyurethane Waterborne Topcoat
Product Codes:

228-3405
228-3410
228-3420
228-3435
228-3450
228-3480

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit paper prior to priming. Primer should be sanded with 280/320 grit paper prior to being coated, The Primer should be coated within eight hours of being sanded. Appropriate primer is the Chemcraft Acquaduro™ Primer 550-1760. When recoating, the previous coat of the Acquaduro™ 2K Polyurethane Waterborne Topcoat must be sanded and the next coat applied within eight hours of being sanded.

General Information:

**After mixing part A and part B to the correct ratio, water can then be added to reduce viscosity prior to application as needed depending on spray equipment. A maximum of 10% water can be added to the fresh (immediately after the part B is fully dispersed into part A) catalyzed material.
Note: Adding extra water during application is not recommended as this will have a direct impact on the pot life. The pot life of the mixture will be reduced significantly and the mixture will gel quickly.
The mixed product contains 876-3400, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of those materials. Refer to MSDS for detailed information. Product must be thoroughly stirred before adding the hardener in the recommended ratio. The viscosity of the product should be monitored after mixing with the hardener. The relative humidity in the application and drying room should not exceed 75% for maximum coating performance. 

PDF Name: CA-PIS_228-34XX_Acquaduro_Pigmented_2K_Polyurethane_Waterborne_Topcoat
Tack Free Time: 20 minutes
Files: CA-PIS_228-34XX_Acquaduro_Pigmented_2K_Polyurethane_Waterborne_Topcoat.pdf
Dry to Sand : 45 minutes
Dry to Stack: 24 hours
Tack Free Time: 12 minutes
Dry to Sand: 20 minutes
VOC less exempt g/l: 174.95
VOC g/l: 75.49
Dry to Stack: 30 minutes
Note: N/A
Note:

--

spec_description:

Acquaduro™ is a pigmented 2K polyurethane waterborne topcoat for industrial application. This product provides excellent water and chemical resistance and has high solids with great hide that allows for ease of application. Whether you are at a finishing shop or at a professional on-site job this low VOC and low odor system meets or exceeds industry standards.

spec_uses:

Acquaduro™ Pigmented 2K Polyurethane Waterborne Topcoat has been designed for the cabinet, architectural millwork, furniture and refinish markets.

Suggested Uses: For cabinet, architectural millwork, furniture, refinish markets.
Mixing Ratio:

8% by volume of 876-3400 Hardener
**See Application Data Notes for additional mixing information**

Pot Life: 3-4 hours depending on external condition
Application Viscosity:

Zahn #2 Signature cup 45-50 sec at 77°F (25° C)
Zahn #3 Signature cup 20-25 sec at 77°F (25° C)

Reducer: Water up to 10% by volume
Retarder: 891-9030 1 to 3% by volume
Clean-up Solvent: Water
Recommended Wet Film: 3-5 wet mils
Coverage:

13.65 m2/L

Note application:

​Polyurethane base should be thoroughly mixed first then Hardener must be Slowly added during agitation, product must be mixed for 1-2 minutes. 

Customer must wait 5 minutes for “induction time” before usage.  Mix only what you can use for 1 to 2 hours at a time.

Viscosity:

Zahn #2 Signature cup 31-35 sec at 77°F (25°C)
Zahn #3 Signature cup 14-18 sec at 77°F (25°C)

Flash Point: 200°F (93.3°C) 9.72 lb/gl 44.55 34.68 6
Density (lb/gal): 1.164
Solid (% by weight): 44.55
Solid (% by volume): 34.68
Shelf Life (months): 12
Acquaduro
423-34XX Acquaduro™ Clear 2K Polyurethane Waterborne Topcoat
Product Codes:

423-3405
423-3410
423-3420
423-3435
423-3450
423-3480

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit paper prior to staining or coating. Sealer should be sanded with 280/320 grit paper prior to being coated, The sealer should be coated within eight hours of being sanded. Self-seal is recommended. When recoating, the previous coat of the Acquaduro™ Clear 2K Polyurethane Waterborne Topcoat must be sanded and the next coat applied within eight hours of being sanded. Recommended stain systems include Promatch Aqua and Promatch C-Mix.

General Information:

**After mixing part A and part B to the correct ratio, water can then be added to reduce viscosity prior to application as needed depending on spray equipment. A maximum of 10% water can be add to the fresh (immediately after the part B is fully dispersed into part A) catalyzed material.
Note: Adding extra water during application is not recommended as this will have a direct impact on the pot life. The pot life of the mixture will be reduce significantly and the mixture will gel quickly.

The mixed product contains 876-3400, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of those materials. Refer to MSDS for detail information. Product must be thoroughly stirred before adding the hardener in the recommended ratio. Oil stains must be avoided because they will interfere with the adhesion. The viscosity of the product should be monitored after mixing with the hardener. The relative humidity in the application and drying room should not exceed 75% for maximum coating performance.

PDF Name: CA-PIS_
Tack Free Time: 20 minutes
Files: CA-PIS_.pdf
Dry to Sand : 45 minutes
Dry to Stack: 24 hours
Tack Free Time: 10 minutes
Dry to Sand: 20 minutes
VOC less exempt g/l: 165.36
VOC g/l: 63.51
Dry to Stack: 30 minutes
Note: N/A
Note:

N/A

spec_description:

Acquaduro™ is a clear 2K polyurethane waterborne topcoat for industrial application. This product provides excellent water and chemical resistance and has high build and excellent feel and appearance. In addition to the enhanced durable features, our 2k waterborne polyurethane topcoat is easy to apply, offers great sandability and has no recoat window. Whether you are at a finishing shop or at a professional on-site job this low VOC and low odor product meets or exceeds industry standards.

spec_uses:

Acquaduro™ Clear 2K Polyurethane Waterborne Topcoat has been designed for the cabinet, architectural millwork, furniture and refinish markets.

Suggested Uses: For cabinet, architectural millwork, furniture, refinish markets.
Mixing Ratio:

8% by volume of 876-3400 Hardener 
**See Application Data Notes section for additional mixing information**

Pot Life: 4 hours at 77°F (25° C)
Application Viscosity:

Zahn #2 Signature cup 45-50 sec at 77°F (25° C)
Zahn #3 Signature cup 20-25 sec at 77°F (25° C)

Reducer: Water up to 10% by volume
Retarder: 891-9030 1 to 3% by volume
Clean-up Solvent: Water
Recommended Wet Film: 6-7 wet mils
Coverage:

12.517 m2/L

Note application:

Polyurethane base should be thoroughly mixed first then Hardener must be Slowly added during agitation, product must be mixed for 1-2 minutes. 

Customer must wait 5 minutes for “induction time” before usage.  Mix only what you can use for 1 to 2 hours at a time.

Viscosity:

Zahn #2 Signature cup 31-35 sec at 77°F (25°C)
Zahn #3 Signature cup 14-18 sec at 77°F (25°C)

Flash Point: > 200°F (93.3°C)
Density (lb/gal): 1.050
Solid (% by weight): 35.7
Solid (% by volume): 31.8
Shelf Life (months): 12
Acquaduro
550-3400 Acquaduro™ 2K Polyurethane Waterborne Primer
Product Codes:

550-3400

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit paper prior to coating. Acquaduro 2K PU WB Primer cannot be used on metal, old oil or cellulose lacquers. For optmum results use 228-34XX Acquaduro Pigmented 2K PU TC or 423-34XX Acquaduro Clear 2K PU TC.  When recoating, the previous coat of Acquaduro 2K PU WB Primer must be sanded and the next coat applied within (8) hours of being sanded.

General Information:

The mixed product contains 876-3400, an isocyanate based co-reactant.  Please follow all precautions associated with handling and use of those materials.  Refer to MSDS for detail information.  Oil stains must be avoided because they will interfere with the adhesion. Product must be thoroughly stirred before adding the hardener in the recommended ratio.  The viscosity of the product should be monitored after mixing with the hardener.  The relative humidity in the application and drying room should not exceed 75% for maximum coating performance. 

PDF Name: CA-PIS_
Tack Free Time: 20 - 30 minutes
Files: CA-PIS_.pdf
Dry to Sand : 60 minutes
Dry to Stack: 3 - 4 hours
Tack Free Time: 15 - 20 minutes
Dry to Sand: 30 - 45 minutes
VOC less exempt g/l: 94.9
VOC g/l: 42.0
Dry to Stack: 60 - 90 minutes
Note: N/A
Note:

N/A

spec_description:

Acquaduro™ 2K PU WB Primer is 2 component polyurethane primer for interior wood and MDF.   The formulation provides superior build, sag resistance, and coverage.  Acquaduro is easy to apply, provide very smooth surface with minimal sanding requirement.

spec_uses:

Acquaduro™ 2K PU WB Primer is designed for the cabinet, architectural millwork, furniture and refinish markets.


Suggested Uses: Interior wood finishes
Mixing Ratio:

7% 876-3400 Hardener by volume

Pot Life: 3 hours
Application Viscosity:

Zahn #3 Signature Cup 18-22 sec at 77˚F (25˚C)


Reducer: Water 3 - 5%
Retarder: 891-9030
Clean-up Solvent: Water
Recommended Wet Film: 4 - 5 mills
Coverage:

15,67 M2/L

Note application:

N/A

Viscosity:

Zahn #3 Signature Cup 18-22 sec at 25 C (77F)

Flash Point: 93.3˚C (>20˚F)
Density (lb/gal): 1.371
Solid (% by weight): 56.44
Solid (% by volume): 39.8
Shelf Life (months): 12

Need help? Contact our team of wood coating experts.

Contact us