New Selva Pro- Isolante Sealer
- 420-1205 Isolante Sealer
- Product Codes:
420-1205
- Surface Preparation:
Wood must be sanded with a #120 or 150 grit paper and free of dust and all contaminants.
- General Information:
Apply 3 to 5 wet mils on a sanded surface. Let dry for 30 to 60 minutes and apply the desired topcoat. If the drying time exceeds 4 hours, sanding is required to keep a good adhesion. Once catalyzed with 876-9084, this product will contain isocyanates. Take necessary precautions for the handling and use of this product. See MSDS.
For a complete system cure, the system must be applied at a temperature above 18ºC and relative humidity below 65%
Complete system must be verified and approved by AkzoNobel before going on production. - PDF Name: CA-PIS_420-1205_Isolante_Sealer
- Tack Free Time: 30-60 minutes
- Files: CA-PIS_420-1205_Isolante_Sealer.pdf
- Dry to Sand : 4 hours
- Dry to Stack: N/A
- Tack Free Time: 15-20 minutes
- Dry to Sand: 30 minutes
- VOC less exempt g/l: 698
- VOC g/l: 698
- Dry to Stack: N/A
- Note:
N/A
- spec_description:
2K Polyurethane. This sealer is designed to improve the adhesion of finishes on difficult substrates like exotic wood.
- spec_uses:
Used as a protective coating for wood, various plastics, oily stain.
For interior usage only - Suggested Uses: Wood Finishes
- Mixing Ratio:
100 Parts 420-1205 with 50 Parts 876-9084 (by volume)
- Pot Life: 4 hours
- Application Viscosity:
20-22 sec Zahn #2 at 77° F (25°C)
- Reducer: 803-2000
- Retarder: N/A
- Clean-up Solvent: 800-5500 Acetone
- Recommended Wet Film: 3-5 wet mils
- Coverage:
N/A
- Note application:
N/A
- Viscosity:
27-29 sec Zahn #2 at 77° F (25°C)
- Flash Point: 21.2° F (9° C)
- Density (lb/gal): 0.84
- Solid (% by weight): 22.8
- Solid (% by volume): 15.2
- Shelf Life (months): 24
- Selva Pro
- 109-17XX Selva™ Pro Bianco Polyurethane Pigmented Topcoat
- Product Codes:
109-1705 Flat
109-1715 Matte
109-1725 Low Gloss
109-1735 Satin
109-1750 Semi-Gloss
109-1780 High Gloss - Surface Preparation:
Substrate must be sanded using 120, 150 or 180 grit paper prior to priming. Primer should be sanded with 280/320 grit paper prior to being coated, The Primer should be coated within eight hours of being sanded. Appropriate primers are the Selva Pro 536-1700, 536-1701, or 536-1702. When recoating, the previous coat of Bianco must be sanded and the next coat applied within eight hours.
- General Information:
The mixed product contains 876-9700, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of those materials. Refer to MSDS for detail information. Oil stains must be avoided because they will interfere with the adhesion.
Product must be thoroughly stirred before adding the hardener in the recommended ratio. The viscosity of the product should be monitored after mixing with the hardener. The relative humidity in the application and drying room should not exceed 75% for maximum coating performance.
- PDF Name: CA-PIS_109-17XX_Selva_Pro_Bianco_Polyurethane_Pigmented_Topcoat
- Tack Free Time: 15 minutes
- Files: CA-PIS_109-17XX_Selva_Pro_Bianco_Polyurethane_Pigmented_Topcoat.pdf
- Dry to Sand : 2 hours
- Dry to Stack: 24 hours
- Tack Free Time: 10 minutes
- Dry to Sand: 30 minutes
- VOC less exempt g/l: 482
- VOC g/l: 482
- Dry to Stack: 1 hour
- Note:
N/A
- spec_description:
Bianco is our pigmented polyurethane system; it is designed to be used in conjunction with our 536 line of primers. Durable and flexible, it can be used as white system or can be tinted to achieve a large range of colors. Builds quickly to help you achieve a high end look when your need is an opaque color.
- spec_uses:
Developed for use in the high end kitchen cabinet market. Its durability will also allow for use in store fixture applications.
- Suggested Uses: Wood Finishes
- Mixing Ratio:
100 Parts 109-17XX with 50 Parts 876-9700 (by volume)
- Pot Life: 2-3 hours depending on temperature and humidity
- Application Viscosity:
Zahn #2 signature cup 22-25 seconds at 25° C
- Reducer: 803-2000
- Retarder: 800-2001 3-5% by volume
- Clean-up Solvent: 800-5500 Acetone
- Recommended Wet Film: 4-6 wet mils
- Coverage:
N/A
- Note application:
MAXIMUM DRY FILM THICKNESS OF THE SYSTEM MUST NOT EXCEED 8 DRY MILS
- Viscosity:
Zahn #3 signature cup 38-42 sec at 25° C
- Flash Point: 7° C
- Density (lb/gal): 1.32
- Solid (% by weight): 64.5
- Solid (% by volume): 45.3
- Shelf Life (months): 24
- Selva Pro
- 109-4995 Selva™ Pro Lucido Polyurethane High Gloss White Topcoat
- Product Codes:
109-4995
- Surface Preparation:
Wood substrate should be sanded with 120 and 150 grit prior to application to ensure good adhesion. Sealers and primers should be well sanded using 240, 280 and 320 grit stearated paper. Suitable primers are polyurethane (536-1700, 536-1701 or 536-1702) or polyester (458-XXXX). For optimal performance primers should be coated within 8 hours of sanding. Care should be taken during sanding to avoid sanding through the primer.
- General Information:
Mix the desired amount of material and apply 3-5 mils wet. The coating when cured is very suitable to be buffed and polished where dust free conditions are not available. Allow product to cure (>24 hours) prior to buffing to reduce shrink-back. The relative humidity in the application and drying rooms should never exceed 75%. Viscosity on the mixed material should be monitored regularly to maintain a consistent appearance.
The mixed product contains 876-9701, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of these materials.
- PDF Name: CA-PIS_109-4995_Selva_Pro_Lucido_Polyurethane_High_Gloss_White_Topcoat
- Tack Free Time: 30-45 minutes
- Files: CA-PIS_109-4995_Selva_Pro_Lucido_Polyurethane_High_Gloss_White_Topcoat.pdf
- Dry to Sand : 8-12 hours
- Dry to Stack: 3 hours
- Tack Free Time: 20-30 minutes
- Dry to Sand: 4-6 hours
- VOC less exempt g/l: 412
- VOC g/l: 412
- Dry to Stack: 2 hours
- Note:
N/A
- spec_description:
Lucido White High Gloss is a high performance, high sheen, two-component polyurethane coating. Lucido gives excellent depth of image, hardness and chemical resistance. Extremely durable with a great finish feel.
- spec_uses:
Great choice for surfaces that require extra chemical resistance. Uses include interior marine and aircraft, cabinetry, store fixtures, and musical instruments.
- Suggested Uses: Wood Finishes
- Mixing Ratio:
1:1 with 876-9701
- Pot Life: 3-4 hours depending on temperature and humidity
- Application Viscosity:
Zahn #2 signature cup 20-25 seconds
- Reducer: 803-2000
- Retarder: 800-2001 3-5% by volume
- Clean-up Solvent: 800-5500 Acetone
- Recommended Wet Film: 4-6 wet mils
- Coverage:
N/A
- Note application:
MAXIMUM DRY FILM THICKNESS OF THE SYSTEM MUST NOT EXCEED 8 DRY MILS
- Viscosity:
Zahn #3 signature cup 30-35 sec at 25° F
- Flash Point: 27° C
- Density (lb/gal): 1.32
- Solid (% by weight): 69.7
- Solid (% by volume): 55.9
- Shelf Life (months): 24
- Selva Pro
- 109-19XX Selva™ Pro Neutral Polyurethane Pigmented Topcoat
- Product Codes:
109-1905 Flat
109-1915 Matte
109-1925 Low Gloss
109-1935 Satin
109-1950 Semi-Gloss
109-1980 High Gloss - Surface Preparation:
Substrate must be sanded using 120, 150 or 180 grit paper prior to priming. Primer should be sanded with 280/320 grit paper prior to being coated, The Primer should be coated within eight hours of being sanded. Appropriate primers are the Selva Pro 536-1700, 536-1701, or 536-1702. When recoating, the previous coat of Bianco must be sanded and the next coat applied within eight hours.
- General Information:
The mixed product contains 876-9700, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of those materials. Refer to MSDS for detail information. Oil stains must be avoided because they will interfere with the adhesion.
Product must be thoroughly stirred before adding the hardener in the recommended ratio. The viscosity of the product should be monitored after mixing with the hardener. The relative humidity in the application and drying room should not exceed 75% for maximum coating performance.
- PDF Name: CA-PIS_109-19XX_Selva_Pro_Neutral_Polyurethane_Pigmented_Topcoat
- Tack Free Time: 15 minutes
- Files: CA-PIS_109-19XX_Selva_Pro_Neutral_Polyurethane_Pigmented_Topcoat.pdf
- Dry to Sand : 3 hours
- Dry to Stack: 24 hours
- Tack Free Time: 10 minutes
- Dry to Sand: 30 minutes
- VOC less exempt g/l: 522
- VOC g/l: 522
- Dry to Stack: 1 hour
- Note:
N/A
- spec_description:
Selva Pro Neutral is our pigmented polyurethane system; it is designed to be used in conjunction with our 536 line of primers. Durable and flexible, it is intended to be tinted to achieve a large range of colors. Builds quickly to help you achieve a high end look when your need is an opaque color.
- spec_uses:
Developed for use in the high end kitchen cabinet market. Its durability will also allow for use in store fixture applications.
- Suggested Uses: Wood Finishes
- Mixing Ratio:
100 Parts 109-19XX with 50 Parts 876-9700 (by volume)
- Pot Life: 2-3 hours depending on temperature and humidity
- Application Viscosity:
Zahn #3 signature cup 22-25 sec at 25° C
- Reducer: 803-2000
- Retarder: 800-2001 3-5% by volume
- Clean-up Solvent: 800-5500 Acetone
- Recommended Wet Film: 4-6 wet mils
- Coverage:
N/A
- Note application:
MAXIMUM DRY FILM THICKNESS OF THE SYSTEM MUST NOT EXCEED 8 DRY MILS
- Viscosity:
Zahn #3 signature cup 27-30 sec at 25° C
- Flash Point: 7° C
- Density (lb/gal): 0.96
- Solid (% by weight): 50.0
- Solid (% by volume): 41.0
- Shelf Life (months): 24
- Selva Pro
- 436-57XX Selva™ Pro Chiaro Polyurethane Clear Topcoat
- Product Codes:
436-5705 Flat
436-5715 Matte
436-5725 Low Gloss
436-5735 Satin
436-5750 Semi-Gloss
436-5780 High Gloss - Surface Preparation:
Substrate must be sanded using 120, 150 or 180 grit paper prior to staining or coating. Sealer should be sanded with 280/320 grit paper prior to being coated. The sealer should be coated within eight hours of being sanded. Appropriate sealer is the Selva Pro Chiaro Sealer 436-5700. When recoating, the previous coat of Chiaro must be sanded and the next coat applied within eight hours. Stain systems used under Chiaro are formulated to develop excellent grain definition.
AkzoNobel recommends using Promatch® W/B Monocolor Spray Stains 824-50XX, Promatch Aqua Stains 824-51XX, Promatch Dye Stains 890-85XX or Promatch C-Mix Wipe Stains 825-90XX, 825-91XX. - General Information:
The mixed product contains 876-9700, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of those materials. Refer to MSDS for detail information. Oil stains must be avoided because they will interfere with the adhesion. When coating exotic woods (Teak, Rosewood, etc.) a barrier coat (tie-coat) should be applied before the sealer or base coat. See Product data sheet for 420-1205
Isolante.
Product must be thoroughly stirred before adding the hardener in the recommended ratio. The viscosity of the product should be monitored after mixing with the hardener. The relative humidity in the application and drying room should not exceed 75% for maximum coating performance. - PDF Name: CA-PIS_436-57XX_Selva_Pro_Chiaro_Polyurethane_Clear_Topcoat
- Tack Free Time: 15 minutes
- Files: CA-PIS_436-57XX_Selva_Pro_Chiaro_Polyurethane_Clear_Topcoat.pdf
- Dry to Sand : 2 hours
- Dry to Stack: 24 hours
- Tack Free Time: 10 minutes
- Dry to Sand: 30 minutes
- VOC less exempt g/l: 545
- VOC g/l: 545
- Dry to Stack: 1 hour
- Note:
N/A
- spec_description:
Chiaro Clear Topcoat is a universal topcoat formulated as an ultra clear polyurethane. Chiaro is a highly versatile polyurethane coating with excellent physical properties and chemical resistance. Extremely durable with a great finish feel. Chiaro also has superior impact resistance.
- spec_uses:
Great choice for surfaces that require extra chemical resistance. Uses include interior marine, cabinetry, store fixtures, and musical instruments.
- Suggested Uses: Wood Finishes
- Mixing Ratio:
100 Parts 436-57XX with 50 Parts 876-9700 (by volume)
- Pot Life: 3-4 hours depending on temperature and humidity
- Application Viscosity:
Zahn #2 signature cup 22-25 seconds.
- Reducer: 803-2000
- Retarder: 800-2001 3-5% by volume
- Clean-up Solvent: 800-5500 Acetone
- Recommended Wet Film: 4-6 wet mils
- Coverage:
N/A
- Note application:
MAXIMUM DRY FILM THICKNESS OF THE SYSTEM MUST NOT EXCEED 6 DRY MILS
- Viscosity:
Zahn #3 signature cup 25-28 sec at 25° C
- Flash Point: 7° C
- Density (lb/gal): 0.96
- Solid (% by weight): 45.45
- Solid (% by volume): 37.25
- Shelf Life (months): 24
Need help? Contact our team of wood coating experts.
