EasyWipe
825-7200 Promatch® Easywipe Neutral
Product Codes:
825-7200 Clear Base
Surface Preparation:
Substrate to be coated should be sanded with 120,150 or 180 grit sandpaper prior to coating. Hand sanding in the direction of the grain after orbital sanding is recommended to minimize sanding marks.
General Information:
Application may be by hand or spray. The stain must be wiped into the grain and wiped clean with a clean rag to ensure good adhesion by subsequent clear coats. If the stain is too dark, the colour strength may be reduced with Easywipe 7200 Clear Base 825-7200.

IMPORTANT: Product must be thoroughly agitated before use.
PDF Name: CA-PIS_825-7200_Promatch_Easywipe_Neutral
Tack Free Time: 1 hour
Files: CA-PIS_825-7200_Promatch_Easywipe_Neutral.pdf
Dry to Sand : N/A
Dry to Stack: N/A
Tack Free Time: 30-40 minutes
Dry to Sand: N/A
VOC less exempt g/l: 664 - 828
VOC g/l: 664 - 828
Dry to Stack: N/A
Note: N/A
Note:
See individual compliance sheets for specific data
spec_description:
Easywipe 7200 stains offer a simple one step stain colour base, good clarity and grain fill with ease of workability. They may be clear coated with any clear system once properly dried.
spec_uses:
Easywipe 7200 stains are all purpose wipe stains for furniture and cabinets. They should be mixed well due to heavy concentration of pigments. Stains are intermixable and reducible.
Suggested Uses: Spray and Wipe
Mixing Ratio:
N/A
Pot Life:
N/A
Application Viscosity:
As Supplied
Reducer: 825-7200 Base
Retarder: N/A
Clean-up Solvent: Lacquer Thinner
Recommended Wet Film: 3-5 wet mils
Coverage:
N/A
Note application:
N/A
Viscosity:
N/A
Flash Point: -26°C (78°F)
Density (lb/gal): 0.93
Solid (% by weight): 10-30%
Solid (% by volume): 7-24%
Shelf Life (months): 24

EasyWipe

825-7200 Promatch® Easywipe Neutral

Find distributor Trouver un distributeur

spec_description:

Easywipe 7200 stains offer a simple one step stain colour base, good clarity and grain fill with ease of workability. They may be clear coated with any clear system once properly dried.

BACKRetour

Product codeCodes de produit
Product Codes:

825-7200 Clear Base

Product information

Product specificationsSpécifications du produit

Viscosity:
N/A
Flash Point: -26°C (78°F)
Density (lb/gal): 0.93
Solid (% by weight): 10-30%
Solid (% by volume): 7-24%
Shelf Life (months): 24

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_825-7200_Promatch_Easywipe_Neutral.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more