- Promatch Spray Stain Base
- 890-2200 Promatch Spray Stain Base
- Product Codes:
890-2200
- Surface Preparation:
Wood substrate must be sanded using 120, 150, or 180 grit paper prior to staining. On wood such as maple, coarser sanding, such as 150 grit, should be performed to avoid polishing of the wood surface. Hand sanding in the direction of the grain following orbital sanding will remove swirl marks.
- General Information:
Product must be thoroughly agitated before use and during application for color consistency. Apply a wet coat of the spray stain on the sanded surface. Let dry a minimum of 30 minutes air dry before the application of the sealer. Keep under mixing to assure consistency of the product. Can be tinted with 844 tints and/or with dyes at a maximum of 6% volume.
- PDF Name: US-PIS_890-2200_Promatch_Spray_Stain_Base
- Tack Free Time: N/A
- Files: US-PIS_890-2200_Promatch_Spray_Stain_Base.pdf
- Dry to Sand : N/A
- Dry to Stack: N/A
- Tack Free Time: N/A
- VOC less exempt lb/gal: <7.15
- Dry to Sand: N/A
- VOC lb/gal: <7.15
- VOC lb/lb Solid: 0.00
- Dry to Stack: N/A
- VHAPs lb/lb Solid: 0.00
- Note:
See individual compliance sheets for specific data.
- spec_description:
Ready to use spray stain that gives little or no grain raising. Formulated especially to be tinted with 844 colorants. Its unique solvent blend also gives the option of using dyes for the development of rich and deep colors.
- spec_uses:
This product is intended for interior wood application.
- Suggested Uses: Wood Stain
- Mixing Ratio:
N/A
- Pot Life: N/A
- Application Viscosity:
N/A
- Reducer: N/A
- Retarder: N/A
- Clean-up Solvent: Acetone or Lacquer Thinner
- Recommended Wet Film: N/A
- Coverage:
N/A
- Note application:
N/A
- Viscosity:
N/A
- Flash Point: 25°F CC
- Density (lb/gal): 7.28 +/-0.20
- Solid (% by weight): 1.89
- Solid (% by volume): 1.42
- Shelf Life (months): 12 mo
- Promatch Spray Stain Base
- Promatch Spray Stain Base
- Product Codes:
890-2200
- Surface Preparation: Clean and sand surface, remove excess dust.
- General Information:
Product must be thoroughly agitated before use and during application for color consistency. Apply a wet coat of the spray stain on the sanded surface. Let dry a minimum of 30 minutes air dry before the application of the sealer. Keep under mixing to assure consistency of the product. Can be tinted with 844 tints and/or with dyes at a maximum of 6% volume.
- PDF Name: US-PIS_Promatch_Spray_Stain_Base
- Tack Free Time: 30 minutes
- Files: US-PIS_Promatch_Spray_Stain_Base.pdf
- Dry to Sand : N/A
- Dry to Stack: N/A
- Tack Free Time: N/A
- VOC less exempt lb/gal: 7.15
- Dry to Sand: N/A
- VOC lb/gal: 7.15
- VOC lb/lb Solid: 0.00
- Dry to Stack: N/A
- VHAPs lb/lb Solid: 0.00
- Note:
See individual compliance sheets for specific data.
- spec_description:
Ready to use spray stain that gives little or no grain raising. Formulated especially to be tinted with 844 colorants. Its unique solvent blend also gives the option of using dyes for the development of rich and deep colors.
- spec_uses:
This product is intended for interior wood application.
- Suggested Uses:
Interior wood application.
- Mixing Ratio:
N/A
- Pot Life:
12 Months
- Application Viscosity:
N/A
- Reducer: N/A
- Retarder: N/A
- Clean-up Solvent: Lacquer Thinner
- Recommended Wet Film: 2-4 mils
- Coverage:
N/A
- Note application:
N/A
- Viscosity:
N/A
- Flash Point: 25°F CC
- Density (lb/gal): 7.28 +/-0.20
- Solid (% by weight): 1.89
- Solid (% by volume): 1.42
- Shelf Life (months): 12
- GLAZE
- 825-3678 Promatch® ProGlaze Neutral Dry Glaze
- Product Codes:
825-3678
- Surface Preparation:
N/A
- General Information:
Prior to use, agitate thoroughly and tint as required with 844 line tints to a maximum of 7% by volume. Apply the Promatch Dry Glaze Neutral over a sealer coat. Sand sealer with 280/320 grit paper before use. The Promatch Dry Glaze Neutral needs to be applied and topcoated within 8 hours of sanding the sealer.
Apply by spray and allow the Promatch Dry Glaze Neutral II to dry before removing excess material with a solvent-wetted rag or Scotch-Brite pad. To ensure good adhesion of the finished system, remove as much of the Promatch Dry Glaze Neutral as possible from the exposed areas before topcoating.
Promatch ProGlaze Neutral Dry Glaze must be thoroughly agitated to ensure product consistency. - PDF Name: US-PIS_825-3678_Promatch_ProGlaze_Neutral_Dry_Glaze
- Tack Free Time: N/A
- Files: US-PIS_825-3678_Promatch_ProGlaze_Neutral_Dry_Glaze.pdf
- Dry to Sand : N/A
- Dry to Stack: N/A
- Tack Free Time: N/A
- VOC less exempt lb/gal: 0.0
- Dry to Sand: N/A
- VOC lb/gal: 0.0
- VOC lb/lb Solid: 0.0
- Dry to Stack: N/A
- VHAPs lb/lb Solid: 0.0
- Note:
The addition of 844 tints will cause an increase in VOC. Therefore a maximum of 6% by volume is required to maintain low VOC requirements (<240 g/l).
- spec_description:
Promatch ProGlaze Neutral Dry Glaze is an all-purpose dry glaze for furniture and cabinets. It is specially formulated to be used with 844 tints and can be tinted up to a maximum of 7% by volume.
- spec_uses:
Promatch ProGlaze Neutral Dry Glaze is used to provide a highlighting effect on furniture, cabinets and millwork. When properly applied, it will provide a highlighted effect with excellent adhesion properties.
- Suggested Uses:
Wood Glaze
- Mixing Ratio:
N/A
- Pot Life: N/A
- Application Viscosity:
N/A
- Reducer: N/A
- Retarder: N/A
- Clean-up Solvent: 800-5500
- Recommended Wet Film: N/A
- Coverage:
N/A
- Note application:
N/A
- Viscosity:
N/A
- Flash Point: 109°F (43°C)
- Density (lb/gal): 11.31
- Solid (% by weight): 9.7%
- Solid (% by volume): 8.43%
- Shelf Life (months): 24
- Glaze
- 825-3680 Promatch® ProGlaze Neutral Wet Glaze
- Product Codes:
825-3680
- Surface Preparation:
N/A
- General Information:
Prior to use, agitate thoroughly and tint as required with 844 line tints to a maximum of 25% by volume. The Promatch® ProGlaze Neutral Wet Glaze can be applied over washcoat, sealer, primer, enamel or topcoat. Must be re-coated with a clear topcoat afterwards. Sand with 280/320 grit paper before applying glaze. The glaze and topcoat must be applied within 8 hours of sanding.
Apply the Glaze by spraying or with a rag. Allow two or three minutes air drying before wiping. Wipe clean and do not leave on any excess material that may interfere with optimum adhesion.
Promatch® ProGlaze Neutral Wet Glaze must be thoroughly agitated to ensure product consistency.
Compatible with 436-48XX ora Verde® Chiaro, 431-46XX Varicure®, 131-53XX Varicure® Select, 421-63XX Chemlife® 24, 117-27XX Chemlife® 24 Plus, etc. - PDF Name: US-PIS_825-3680_Promatch_ProGlaze_Neutral_Wet_Glaze
- Tack Free Time: N/A
- Files: US-PIS_825-3680_Promatch_ProGlaze_Neutral_Wet_Glaze.pdf
- Dry to Sand : N/A
- Dry to Stack: N/A
- Tack Free Time: N/A
- VOC less exempt lb/gal: 5.1
- Dry to Sand: N/A
- VOC lb/gal: 5.1
- VOC lb/lb Solid: 2.42
- Dry to Stack: N/A
- VHAPs lb/lb Solid: 0.03
- Note:
N/A
- spec_description:
Promatch® ProGlaze Neutral Wet Glaze is an all-purpose wet glaze for furniture and cabinets. It is specially formulated to be used with 844 tints and can be tinted up to a maximum of 25% by volume. This universal solvent borne glaze provides good adhesion and workability with various technologies such as pre-cats, conversion varnishes and 2k polyurethane.
- spec_uses:
Promatch® ProGlaze Neutral Wet Glaze is used for coloring of wood on furniture, cabinets and millwork. When properly applied, it will enhance the natural beauty of the wood.
- Suggested Uses:
Wood Glaze
- Mixing Ratio:
N/A
- Pot Life: N/A
- Application Viscosity:
N/A
- Reducer: N/A
- Retarder: N/A
- Clean-up Solvent: 803-1298
- Recommended Wet Film: N/A
- Coverage:
N/A
- Note application:
Applied spray or with rag, allow to dry, wipe or brush. Allow to dry.
- Viscosity:
N/A
- Flash Point: >200°F
- Density (lb/gal): 7.19
- Solid (% by weight): 29.2%
- Solid (% by volume): 21.8%
- Shelf Life (months): 24
- AQUA DRY GLAZE Base
- 824-17XX Promatch® Aqua 275 / 550 BA Glaze WB Stain
- Product Codes:
824-1715 Black
824-1716 Brown
824-1718 Natural
824-1721 Walnut
824-1722 White - Surface Preparation:
N/A
- General Information:
Apply the BA Glaze by spraying. Allow to dry and then brush off.
BA Glaze must be thoroughly agitated to ensure product consistency.
The completed coating system should be checked for required properties prior to start-up of production.
IMPORTANT: Product must be thoroughly agitated before use.
- PDF Name: US-PIS_824-17XX_Promatch_Aqua_275_-_550_BA_Glaze_WB_Stain
- Tack Free Time: N/A
- Files: US-PIS_824-17XX_Promatch_Aqua_275_-_550_BA_Glaze_WB_Stain.pdf
- Dry to Sand : N/A
- Dry to Stack: N/A
- Tack Free Time: N/A
- VOC less exempt lb/gal: <2.7
- Dry to Sand: N/A
- VOC lb/gal: <0.45
- VOC lb/lb Solid: <0.16
- Dry to Stack: N/A
- VHAPs lb/lb Solid: <0.00
- Note:
See individual compliance sheets for specific data
- spec_description:
BA Glaze 824-17XX is an all-purpose break-away glaze for furniture and cabinets.
- spec_uses:
BA Glaze is used for coloring of wood and is especially developed for furniture coating systems. BA Glaze is recommended for indoor use.
- Suggested Uses:
Wood Glaze
- Mixing Ratio:
N/A
- Pot Life:
N/A
- Application Viscosity:
N/A
- Reducer: N/A
- Retarder: N/A
- Clean-up Solvent: 800-5500
- Recommended Wet Film: N/A
- Coverage:
N/A
- Note application:
N/A
- Viscosity:
N/A
- Flash Point: N/A
- Density (lb/gal): 8.29 – 9.51
- Solid (% by weight): 15.5% - 32.7%
- Solid (% by volume): 6.4% - 12.1%
- Shelf Life (months): 24
Need help? Contact our team of wood coating experts.
