Glaze
825-1892 Chemglaze Clear
Product Codes:

825-1892

Surface Preparation:

Substrate must be sanded using 120, 150 or 180 grit stearated paper prior to glazing. Sealers should be sanded immediately prior to being coated with 280/320 grit stearated paper. 

General Information:

Prior to use, mix Chemglaze Clear carefully and reduce viscosity by adding approximately 50-100% reducer. Apply the reduced Chemglaze Clear by spraying or with a rag. Allow two to three minutes air drying before wiping. Wipe clean and do not leave on any excess material that may interfere with optimum adhesion. Chemglaze Clear must be thoroughly agitated to ensure product consistency.

Wipe on using a clean dry rag or spray on. Leave 2 - 3 minutes and wipe off. Air dry 45 to 60 minutes or air dry for 15 minutes at room temperature followed by at least 15 minutes at 158˚F. The customer is resonsible for following the recommended application precedures. Failure to adhere to the recommendations given in this Technical Data Sheet will likely result in unstaisfactory film appearance or film failure. The completed coating system should be checked for required properties prior to start-up of production. Product must be thoroughly agitated before use.

PDF Name: US-PIS_825-1892_Chemglaze_Clear
Tack Free Time: N/A
Files: US-PIS_825-1892_Chemglaze_Clear.pdf
Dry to Sand : N/A
Dry to Stack: N/A
Tack Free Time: N/A
VOC less exempt lb/gal: 5.31
Dry to Sand: N/A
VOC lb/gal: 5.31
VOC less exempt g/l: 637
VOC g/l: 637
VOC lb/lb Solid: 2.29
Dry to Stack: N/A
VHAPs lb/lb Solid: 0.27
Note: N/A
Note:

N/A

spec_description:

Chemglaze clear 825-1892 is an all-purpose neutral glaze for furniture and cabinets.

spec_uses:

Used for coloring and enhancing the natural beauty of the wood

Suggested Uses:

Wood Glaze

Mixing Ratio:

N/A

Pot Life: N/A
Application Viscosity:

N/A

Reducer: 801-1202
Retarder: N/A
Clean-up Solvent: Lacquer Thinner
Recommended Wet Film: N/A
Coverage:

N/A

Note application:

N/A

Viscosity:

2350 cps

Flash Point: 60.8°F (16°C)
Density (lb/gal): 7.64
Solid (% by weight): 30.4%
Solid (% by volume): 21.2%
Shelf Life (months): 12
Promatch Spray Stain Base
890-2200 Promatch Spray Stain Base
Product Codes:

890-2200

Surface Preparation:

Wood substrate must be sanded using 120, 150, or 180 grit paper prior to staining.  On wood such as maple, coarser sanding, such as 150 grit, should be performed to avoid polishing of the wood surface.  Hand sanding in the direction of the grain following orbital sanding will remove swirl marks.

General Information:

Product must be thoroughly agitated before use and during application for color consistency. Apply a wet coat of the spray stain on the sanded surface. Let dry a minimum of 30 minutes air dry before the application of the sealer. Keep under mixing to assure consistency of the product. 

Product can be tinted with 844 tints up 10% by volume and/or with 890-12XX dyes at a maximum of 3% by volume.


PDF Name: US-PIS_890-2200_Promatch_Spray_Stain_Base
Tack Free Time: N/A
Files: US-PIS_890-2200_Promatch_Spray_Stain_Base.pdf
Dry to Sand : N/A
Dry to Stack: N/A
Tack Free Time: N/A
VOC less exempt lb/gal: <7.15
Dry to Sand: N/A
VOC lb/gal: <7.15
VOC less exempt g/l: <51.90
VOC g/l: <503.99
VOC lb/lb Solid: 0.00
Dry to Stack: N/A
VHAPs lb/lb Solid: 0.00
Note: N/A
Note:

See individual compliance sheets for specific data.


spec_description:

Ready to use spray stain that gives little or no grain raising. Formulated especially to be tinted with 844 colorants. Its unique solvent blend also gives the option of using dyes for the development of rich and deep colors.

spec_uses:

This product is intended for interior wood application. 

Suggested Uses: Wood Stain
Mixing Ratio:

N/A

Pot Life: N/A
Application Viscosity:

N/A

Reducer: N/A
Retarder: N/A
Clean-up Solvent: Acetone or Lacquer Thinner
Recommended Wet Film: N/A
Coverage:

N/A

Note application:

N/A

Viscosity:

N/A

Flash Point: 25°F CC
Density (lb/gal): 7.28 +/-0.20
Solid (% by weight): 1.89
Solid (% by volume): 1.42
Shelf Life (months): 12 mo
Glaze
825-3680 Promatch® ProGlaze Neutral Wet Glaze
Product Codes:

825-3680

Surface Preparation:

N/A

General Information:

Prior to use, agitate thoroughly and tint as required with 844 line tints to a maximum of 25% by volume. The Promatch® ProGlaze Neutral Wet Glaze can be applied over washcoat, sealer, primer, enamel or topcoat. Must be re-coated with a clear topcoat afterwards. Sand with 280/320 grit paper before applying glaze. The glaze and topcoat must be applied within 8 hours of sanding.

Apply the Glaze by spraying or with a rag. Allow two or three minutes air drying before wiping. Wipe clean and do not leave on any excess material that may interfere with optimum adhesion.

Promatch® ProGlaze Neutral Wet Glaze must be thoroughly agitated to ensure product consistency.
Compatible with 436-48XX ora Verde® Chiaro, 431-46XX Varicure®, 131-53XX Varicure® Select, 421-63XX Chemlife® 24, 117-27XX Chemlife® 24 Plus, etc. 


PDF Name: US-PIS_825-3680_Promatch_ProGlaze_Neutral_Wet_Glaze
Tack Free Time: N/A
Files: US-PIS_825-3680_Promatch_ProGlaze_Neutral_Wet_Glaze.pdf
Dry to Sand : N/A
Dry to Stack: N/A
Tack Free Time: N/A
VOC less exempt lb/gal: 5.1
Dry to Sand: N/A
VOC lb/gal: 5.1
VOC less exempt g/l: 612
VOC g/l: 612
VOC lb/lb Solid: 2.42
Dry to Stack: N/A
VHAPs lb/lb Solid: 0.03
Note: N/A
Note:

N/A

spec_description:

Promatch® ProGlaze Neutral Wet Glaze is an all-purpose wet glaze for furniture and cabinets. It is specially formulated to be used with 844 tints and can be tinted up to a maximum of 25% by volume. This universal solvent borne glaze provides good adhesion and workability with various technologies such as pre-cats, conversion varnishes and 2k polyurethane.

spec_uses:

Promatch® ProGlaze Neutral Wet Glaze is used for coloring of wood on furniture, cabinets and millwork. When properly applied, it will enhance the natural beauty of the wood.

Suggested Uses:

Wood Glaze

Mixing Ratio:

N/A

Pot Life: N/A
Application Viscosity:

N/A

Reducer: N/A
Retarder: N/A
Clean-up Solvent: 803-1298
Recommended Wet Film: N/A
Coverage:

N/A

Note application:

Applied spray or with rag, allow to dry, wipe or brush.  Allow to dry.

Viscosity:

N/A

Flash Point: >200°F
Density (lb/gal): 7.19
Solid (% by weight): 29.2%
Solid (% by volume): 21.8%
Shelf Life (months): 24
Promatch Spray Stain Base
Promatch Spray Stain Base
Product Codes:

890-2200

Surface Preparation: Clean and sand surface, remove excess dust.
General Information:

Product must be thoroughly agitated before use and during application for color consistency. Apply a wet coat of the spray stain on the sanded surface. Let dry a minimum of 30 minutes air dry before the application of the sealer. Keep under mixing to assure consistency of the product. Can be tinted with 844 tints and/or with dyes at a maximum of 6% volume.


PDF Name: US-PIS_Promatch_Spray_Stain_Base
Tack Free Time: 30 minutes
Files: US-PIS_Promatch_Spray_Stain_Base.pdf
Dry to Sand : N/A
Dry to Stack: N/A
Tack Free Time: N/A
VOC less exempt lb/gal: 7.15
Dry to Sand: N/A
VOC lb/gal: 7.15
VOC less exempt g/l: 51.90
VOC g/l: 503.99
VOC lb/lb Solid: 0.00
Dry to Stack: N/A
VHAPs lb/lb Solid: 0.00
Note: N/A
Note:

See individual compliance sheets for specific data.


spec_description:

Ready to use spray stain that gives little or no grain raising. Formulated especially to be tinted with 844 colorants. Its unique solvent blend also gives the option of using dyes for the development of rich and deep colors.

spec_uses:

This product is intended for interior wood application. 

Suggested Uses:

Interior wood application.

Mixing Ratio:

N/A

Pot Life:

12 Months

Application Viscosity:

N/A

Reducer: N/A
Retarder: N/A
Clean-up Solvent: Lacquer Thinner
Recommended Wet Film: 2-4 mils
Coverage:

N/A

Note application:

N/A

Viscosity:

N/A

Flash Point: 25°F CC
Density (lb/gal): 7.28 +/-0.20
Solid (% by weight): 1.89
Solid (% by volume): 1.42
Shelf Life (months): 12
GLAZE
825-3678 Promatch® ProGlaze Neutral Dry Glaze
Product Codes:

825-3678

Surface Preparation:

N/A

General Information:

Prior to use, agitate thoroughly and tint as required with 844 line tints to a maximum of 7% by volume. Apply the Promatch Dry Glaze Neutral  over a sealer coat. Sand sealer with 280/320 grit paper before use. The Promatch Dry Glaze Neutral  needs to be applied and topcoated within 8 hours of sanding the sealer.

Apply by spray and allow the Promatch Dry Glaze Neutral II to dry before removing excess material with a solvent-wetted rag or Scotch-Brite pad. To ensure good adhesion of the finished system, remove as much of the Promatch Dry Glaze Neutral as possible from the exposed areas before topcoating.

Promatch ProGlaze Neutral Dry Glaze must be thoroughly agitated to ensure product consistency.

PDF Name: US-PIS_825-3678_Promatch_ProGlaze_Neutral_Dry_Glaze
Tack Free Time: N/A
Files: US-PIS_825-3678_Promatch_ProGlaze_Neutral_Dry_Glaze.pdf
Dry to Sand : N/A
Dry to Stack: N/A
Tack Free Time: N/A
VOC less exempt lb/gal: 0.0
Dry to Sand: N/A
VOC lb/gal: 0.0
VOC less exempt g/l: 0.0
VOC g/l: 0.0
VOC lb/lb Solid: 0.0
Dry to Stack: N/A
VHAPs lb/lb Solid: 0.0
Note: N/A
Note:

The addition of 844 tints will cause an increase in VOC.  Therefore a maximum of 6% by volume is required to maintain low VOC requirements  (<240 g/l).

spec_description:

Promatch ProGlaze Neutral Dry Glaze is an all-purpose dry glaze for furniture and cabinets. It is specially formulated to be used with 844 tints and can be tinted up to a maximum of 7% by volume. 

spec_uses:

Promatch ProGlaze Neutral Dry Glaze is used to provide a highlighting effect on furniture, cabinets and millwork. When properly applied, it will provide a highlighted effect with excellent adhesion properties.

Suggested Uses:

Wood Glaze

Mixing Ratio:

N/A

Pot Life: N/A
Application Viscosity:

N/A

Reducer: N/A
Retarder: N/A
Clean-up Solvent: 800-5500
Recommended Wet Film: N/A
Coverage:

N/A

Note application:

N/A

Viscosity:

N/A

Flash Point: 109°F (43°C)
Density (lb/gal): 11.31
Solid (% by weight): 9.7%
Solid (% by volume): 8.43%
Shelf Life (months): 24

Need help? Contact our team of wood coating experts.

Contact us