Glaze
825-1892 Chemglaze Clear
Product Codes:
825-1892
Surface Preparation:
Substrate must be sanded using 120, 150 or 180 grit stearated paper prior to glazing. Sealers should be sanded immediately prior to being coated with 280/320 grit stearated paper.
General Information:
Prior to use, mix Chemglaze Clear carefully and reduce viscosity by adding approximately 50-100% reducer. Apply the reduced Chemglaze Clear by spraying or with a rag. Allow two to three minutes air drying before wiping. Wipe clean and do not leave on any excess material that may interfere with optimum adhesion. Chemglaze Clear must be thoroughly agitated to ensure product consistency.
Wipe on using a clean dry rag or spray on. Leave 2 - 3 minutes and wipe off. Air dry 45 to 60 minutes or air dry for 15 minutes at room temperature followed by at least 15 minutes at 158˚F. The customer is resonsible for following the recommended application precedures. Failure to adhere to the recommendations given in this Technical Data Sheet will likely result in unstaisfactory film appearance or film failure. The completed coating system should be checked for required properties prior to start-up of production. Product must be thoroughly agitated before use.
PDF Name: US-PIS_825-1892_Chemglaze_Clear
Tack Free Time: N/A
Files: US-PIS_825-1892_Chemglaze_Clear.pdf
Dry to Sand : N/A
Dry to Stack: N/A
Tack Free Time: N/A
VOC less exempt lb/gal: 5.31
Dry to Sand: N/A
VOC lb/gal: 5.31
VOC less exempt g/l: 637
VOC g/l: 637
VOC lb/lb Solid: 2.29
Dry to Stack: N/A
VHAPs lb/lb Solid: 0.27
Note: N/A
Note:
N/A
spec_description:
Chemglaze clear 825-1892 is an all-purpose neutral glaze for furniture and cabinets.
spec_uses:
Used for coloring and enhancing the natural beauty of the wood
Suggested Uses:
Wood Glaze
Mixing Ratio:
N/A
Pot Life: N/A
Application Viscosity:
N/A
Reducer: 801-1202
Retarder: N/A
Clean-up Solvent: Lacquer Thinner
Recommended Wet Film: N/A
Coverage:
N/A
Note application:
N/A
Viscosity:
2350 cps
Flash Point: 60.8°F (16°C)
Density (lb/gal): 7.64
Solid (% by weight): 30.4%
Solid (% by volume): 21.2%
Shelf Life (months): 12

Glaze

825-1892 Chemglaze Clear

Find distributor Trouver un distributeur

spec_description:

Chemglaze clear 825-1892 is an all-purpose neutral glaze for furniture and cabinets.

BACKRetour

Product codeCodes de produit
Product Codes:

825-1892

Product information

Product specificationsSpécifications du produit

Viscosity:
2350 cps
Flash Point: 60.8°F (16°C)
Density (lb/gal): 7.64
Solid (% by weight): 30.4%
Solid (% by volume): 21.2%
Shelf Life (months): 12

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: US-PIS_825-1892_Chemglaze_Clear.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more