Selva Pro

436-4995 Selva™ Pro Lucido Polyurethane High Gloss Clear Topcoat

Product Codes:

436-4995

Surface Preparation:

Wood substrate should be sanded with 120 and 150 grit prior to application to ensure good adhesion. Sealers should be well sanded using 320 grit stearated paper. Suitable sealer is Chiaro (436-5700) or polyester (458-XXXX). For optimal performance sealers should be coated within 8 hours of sanding. Difficult or oily wood substrates may require Isolante sealer (420-1205). It is not recommended to use traditional oil stains with polyurethane products.

General Information:

Mix the desired amount of material and apply 4-6 mils wet. The coating when cured is very suitable to be buffed and polished where dust free conditions are not available. Allow product to cure (>24 hours) prior to buffing to reduce shrink-back. The relative humidity in the application and drying rooms should never exceed 75%. Viscosity on the mixed material should be monitored regularly to maintain a consistent appearance.

The mixed product contains 876-9701, an isocyanate based co-reactant. Please follow all precautions associated with handling and use of these materials.

PDF Name: CA-PIS_436-4995_Selva_Pro_Lucido_Polyurethane_High_Gloss_Clear_Topcoat

Tack Free Time: 30-45 minutes

Files: CA-PIS_436-4995_Selva_Pro_Lucido_Polyurethane_High_Gloss_Clear_Topcoat.pdf

Dry to Sand : 3 hours

Dry to Stack: 3 hours

Tack Free Time: 20-30 minutes

Dry to Sand: 2 hours

VOC less exempt g/l: 444

VOC g/l: 444

Dry to Stack: 2 hours

Note: N/A

Note:

See individual compliance sheets for specific data

spec_description:

Selva Pro Lucido HG is a two-component polyurethane clear topcoat featuring a high cross-linked density film for a maximum wet look finish.It can be cut and polished easily making it ideal for high-end woodwork offering high build with high gloss reten-tion and clarity. It can tinted with 844's to obtain a wide range of darker colors.

spec_uses:

Great choice where a very high gloss finish is required. Uses include interior cabinetry, interior marine and aircraft cabinetry, store fixtures, and musical instruments.

Suggested Uses: Wood Finishes

Mixing Ratio:

1:1 with 876-9701

Pot Life: 3-4 hours depending on temperature and humidity

Application Viscosity:

Zahn #2 signature cup 20-25 seconds.

Reducer: 803-2000

Retarder: 800-2001 3-5% by volume

Clean-up Solvent: 800-5500 Acetone

Recommended Wet Film: 4-6 wet mils

Coverage:

N/A

Note application:

MAXIMUM DRY FILM THICKNESS OF THE SYSTEM MUST NOT EXCEED 6 DRY MILS

Viscosity:

Zahn #2 signature cup 48-52 sec at 25° C

Flash Point: 27° C

Density (lb/gal): 0.96

Solid (% by weight): 57.0

Solid (% by volume): 50.0

Shelf Life (months): 24

Selva Pro

436-4995 Selva™ Pro Lucido Polyurethane High Gloss Clear Topcoat

Find distributor Trouver un distributeur

spec_description:

BACKRetour

Selva Pro

436-4995 Selva™ Pro Lucido Polyurethane High Gloss Clear Topcoat

spec_description:

Product codeCodes de produit
Product Codes:

436-4995

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 48-52 sec at 25° C

Flash Point: 27° C

Density (lb/gal): 0.96

Solid (% by weight): 57.0

Solid (% by volume): 50.0

Shelf Life (months): 24

UsesUtilisations

Environmental data (as supplied)Données environnementales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_436-4995_Selva_Pro_Lucido_Polyurethane_High_Gloss_Clear_Topcoat.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommanded for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro, apprêt à catalyser est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap