Promatch®

825-34XX Promatch® Dry Glaze

Product Codes:

825-3410 Neutral Base

825-3411 White Base

825-3414 Yellow tint

825-3415 Brown tint

825-3416 Black tint

825-3417 Red tint

Surface Preparation:

The substrate must be sanded with a #120, 150 or 180 grit sand paper and free of dust and all contaminants.

General Information:

Apply Dry Glaze at approximately 3-4 mils wet over sealer coat. Allow to flash off and remove excess material with a solvent‑wetted rag or "Scotch‑Brite" pad. To ensure good adhesion of the finished system, as much filler as possible should be removed from the exposed areas.

825-3410 and 825-3411 are designed to be tinted with Dry Glaze Tints from the 825-34XX line, the use of liquid tinters will complicate the removal process and is not recommended.

PDF Name: CA-PIS_825-34XX_Promatch_Dry_Glaze

Tack Free Time: 15 - 20 minutes

Files: CA-PIS_825-34XX_Promatch_Dry_Glaze.pdf

Dry to Sand : 15 - 20 minutes

Dry to Stack: N/A

Tack Free Time: N/A

Dry to Sand: 10 -15 minutes

VOC less exempt g/l: 766 Neutral 755 White, 684-696 Tints

VOC g/l: 766 Neutral 755 White, 684-696 Tints

Dry to Stack: N/A

Note: N/A

Note:

See individual compliance sheets for specific data.

spec_description:

Concentrated pigment dispersion designed to provide an antiquated effect to furniture, cabinets and paneling.

spec_uses:

Use as protective coatings on all type of wood.

For interior use only.

Suggested Uses: Spray

Mixing Ratio:

N/A

Pot Life: N/A

Application Viscosity:

As is

Reducer: N/A

Retarder: N/A

Clean-up Solvent: Lacquer Thinner

Recommended Wet Film: 2-4 mils wet

Coverage:

N/A

Note application:

N/A

Viscosity:

Zahn #2 signature cup 13 sec at 25°C (Neutral)

Zahn #2 signature cup 18 sec at 25°C (White)

Flash Point: 12°C Neutral/White base, 7°C Tints

Density (lb/gal): @25°C 0.92 White, 0.86 Neutral/Tints

Solid (% by weight): 10% Neutral, 18% White, 20% Tints

Solid (% by volume): 4% Neutral, 6% White, 12-13% Tints

Shelf Life (months): 24

Promatch®

825-34XX Promatch® Dry Glaze

Find distributor Trouver un distributeur

spec_description:

Concentrated pigment dispersion designed to provide an antiquated effect to furniture, cabinets and paneling.

BACK

Promatch®

825-34XX Promatch® Dry Glaze

spec_description:

Concentrated pigment dispersion designed to provide an antiquated effect to furniture, cabinets and paneling.

Product codeCodes de produit
Product Codes:

825-3410 Neutral Base

825-3411 White Base

825-3414 Yellow tint

825-3415 Brown tint

825-3416 Black tint

825-3417 Red tint

Product information

Product specificationsSpécifications du produit

Viscosity:

Zahn #2 signature cup 13 sec at 25°C (Neutral)

Zahn #2 signature cup 18 sec at 25°C (White)

Flash Point: 12°C Neutral/White base, 7°C Tints

Density (lb/gal): @25°C 0.92 White, 0.86 Neutral/Tints

Solid (% by weight): 10% Neutral, 18% White, 20% Tints

Solid (% by volume): 4% Neutral, 6% White, 12-13% Tints

Shelf Life (months): 24

UsesUtilisations

Environmental data (as supplied)Données environmentales (tel que fourni)

Application dataDonnées d'application

Surface PreparationPréparation de la surface

General InformationInformations générales

Drying TimesTemps de séchage

Find distributor Trouver un distributeur

Download product information sheets

Files: CA-PIS_825-34XX_Promatch_Dry_Glaze.pdf

These products are designed for industrial use only. AkzoNobel views safety as a top priority. Please refer to Material Safety Data Sheet for information on the safe use of this product.

Dry times are greatly affected by film build, porosity of substrate, air movement as well as heat and humidity. Temperatures are based on actual board temperature. This may vary depending on length of time for boards to reach these temperatures. Minimum curing temperatures of 64°F/18°C must be maintained throughout the curing cycle to achieve the film integrity as stated in product features.

Recommended for interior woodwork

OmniBuild Pro Conversion Varnish Primer Surfacer is recommended for interior woodwork on solid wood and MDF.

Recommandé pour les boiseries intérieures

OmniBuild Pro Conversion Varnish Primer Surfacer est recommandé pour les travaux de menuiserie intérieure sur bois massif et MDF.

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

View our ranges

Our extensive wood coatings expertise covers all technologies. From pre-catalyzed to waterborne, nitrocellulose to polyurethane, we deliver a wide range of top-performing products for your business.

Learn more

About our brand	Products	Distributors	Using our products
Contact us	Pre-Catalyzed	Our Distributors	How-to-videos
	Post-Catalyzed	Our Ordering portals	Troubleshooting Guides
	Polyurethane		Glossary of Terms
	Waterborne		Associations
	Color Systems		Mobile Product App
	Vinyl Products
	Nitrocellulose
	Specialty Products

Cookies	Cookie settings	Privacy	Sitemap